Summary for Test 2020-03-24-8-7
Test performed: ASTM F606-14Project Information
Project Identifiers | Project ID: 214421 DEA: 01362704 EFIS: 0116000031 |
---|---|
DIST-CO-RTE-PM | 01-MEN-1-62.2/R78.9 |
Award Date | 12/23/2019 |
Closeout Date | 03/09/2021 |
Work Description | HOT MIX ASPHALT OVERLAY. |
Location Description | MENDOCINO COUNTY NEAR FORT BRAGG FROM 0.1 MILE NORTH OF PUDDING CREEK BRIDGE TO 0.6 MILE NORTH OF WAGES CREEK BRIDGE |
QA Service Level | 1 (Verified on 09/19/2019) |
Sample Information
Sample Taken Date | 03/24/2020 | Sample Unique Key | 8 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 04/10/2020 |
Sample type | Quality Assurance | A brief description of the sample | ASTM A193 B7 Stud |
The quantity of what the sample constitutes | 200 pieces | From where was the sample collected | Fabricator |
First name of sampler or witnessed by | Mahlon | Last name of sampler or witnessed by | Lindenmuth |
Title of sampler | QA Inspector | Telephone number of sampler | 646-740-3704 |
Laboratory sample identification | Linked DIME Sample ID | ||
The fabricator/manufacturer/facility name | BAY STANARD MANUFACTURING | Transportation Laboratory (TL) Number | |
Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
Structure name |
Material Information
Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | N/A |
---|---|---|---|
Heat Number(s) | 10599080 | Nut Mfg. Lot Number(s) | N/A |
Washer Mfg. Lot Number(s) | N/A | Bolt Specification | ASTM A193 B7 |
Bolt Length(s) | 18" | Nut Specification | N/A |
Washer Specification | N/A | Finish | ASTM A153 HDG |
Diameter/Size | 3/4" | Bolt Mfg. Lot Number | 2002171A-4 |
Rocap Test Requirement(s) | NO | Lubricant Requirements(s) | NO |
Test Details
DIME Sample ID: 2020-03-24-8
DIME Test ID: 2020-03-24-8-7
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2020-04-15
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: bewing
Date of test: 04/15/2020
UTM: 400kip
Temperature: 72
Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
---|---|---|---|---|---|---|---|---|---|
1 | 7 | UNC 3/4 | 0.334 | 45883 | 204 | 137374 | 127899 | 42718 | A193 B7 Stud |
General comments (publicly viewable) (Max 1000 characters): A193 B7 Stud
Test Graph
Source: Bluehill Data Point FileTest was verified on 4/15/2020 ✔