Summary for Test 2018-05-25-3-1
Test performed: ASTM F606-14Project Information
Project Identifiers | Project ID: 212354 DEA: 044K8504 EFIS: 0417000378 |
---|---|
DIST-CO-RTE-PM | 04-MRN,MTRN-1-22.8, 22.80 |
Award Date | 06/21/2017 |
Closeout Date | 12/16/2021 |
Work Description | Giacomini Creek Bridge, Construct sheet pile wall, replace culvert |
Location Description | ROUTE 1, AT POSTMILE 22.8, NEAR BOLINAS, AT 0.52 MILES NORTH OF HORSESHOE HILL RD., MARIN COUNTY SLIPOUT, CONSTRUCT SOLDIER PILE WALL |
QA Service Level | 1 (Verified on 05/01/2017) |
Sample Information
Sample Taken Date | 05/25/2018 | Sample Unique Key | 3 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 05/25/2018 |
Sample type | Quality Assurance | A brief description of the sample | 3/4 X 4-1/2, 3/4 X 5-1/2, 7/8 X 19-1/2 |
The quantity of what the sample constitutes | Lot of 28 | From where was the sample collected | Fabricator |
First name of sampler or witnessed by | Scott | Last name of sampler or witnessed by | Leavitt |
Title of sampler | QA Inspector | Telephone number of sampler | 510 590-0116 |
Laboratory sample identification | Unknown | Linked DIME Sample ID | Unknown |
The fabricator/manufacturer/facility name | Portland Bolt Manufacturing | Transportation Laboratory (TL) Number | Unknown |
Inspector Lot Number from the Transportation Laboratory (TL) Form | S28-126-18 | Structure unique identifier | Not set |
Structure name | Not set |
Material Information
Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | 110135-1, 110135-2 |
---|---|---|---|
Heat Number(s) | NF16100667, 10483100, 3065481 | Nut Mfg. Lot Number(s) | 400279E |
Washer Mfg. Lot Number(s) | 0118-742 | Bolt Specification | A325, A325, A449 |
Bolt Length(s) | 4-1/2, 5-1/2, 19-1/2 | Nut Specification | A563DH |
Washer Specification | F436-1 | Finish | HDG, HDG, HDG |
Diameter/Size | 3/4, 3/4, 7/8 | Bolt Mfg. Lot Number | Nucor, Fontana Fasteners, Portland Bolt |
Rocap Test Requirement(s) | Yes, Yes, No | Lubricant Requirements(s) | Yes, Yes |
Test Details
DIME Sample ID: 2018-05-25-3
DIME Test ID: 2018-05-25-3-1
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2018-06-07
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Brian
Date of test: 05/30/2018
UTM: 400KIP
Temperature: 72
Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
---|---|---|---|---|---|---|---|---|---|
1 | 3A | A449 Bolt | 0.462 | 60712 | 270 | 131411 | 118617 | 54801 | A449 Bolt |
General comments (publicly viewable) (Max 1000 characters): A449 Bolt
Test Graph
Source: Partner Data Point FileTest was verified on 5/31/2018 ✔