Summary for Test 2020-03-24-8-2
Test performed: ASTM F606-14Project Information
| Project Identifiers | Project ID: 214421 DEA: 01362704 EFIS: 0116000031 |
|---|---|
| DIST-CO-RTE-PM | 01-MEN-1-62.2/R78.9 |
| Award Date | 12/23/2019 |
| Closeout Date | 03/09/2021 |
| Work Description | HOT MIX ASPHALT OVERLAY. |
| Location Description | MENDOCINO COUNTY NEAR FORT BRAGG FROM 0.1 MILE NORTH OF PUDDING CREEK BRIDGE TO 0.6 MILE NORTH OF WAGES CREEK BRIDGE |
| QA Service Level | 1 (Verified on 09/19/2019) |
Sample Information
| Sample Taken Date | 03/24/2020 | Sample Unique Key | 8 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 04/10/2020 |
| Sample type | Quality Assurance | A brief description of the sample | ASTM A193 B7 Stud |
| The quantity of what the sample constitutes | 200 pieces | From where was the sample collected | Fabricator |
| First name of sampler or witnessed by | Mahlon | Last name of sampler or witnessed by | Lindenmuth |
| Title of sampler | QA Inspector | Telephone number of sampler | 646-740-3704 |
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | BAY STANARD MANUFACTURING | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | N/A |
|---|---|---|---|
| Heat Number(s) | 10599080 | Nut Mfg. Lot Number(s) | N/A |
| Washer Mfg. Lot Number(s) | N/A | Bolt Specification | ASTM A193 B7 |
| Bolt Length(s) | 18" | Nut Specification | N/A |
| Washer Specification | N/A | Finish | ASTM A153 HDG |
| Diameter/Size | 3/4" | Bolt Mfg. Lot Number | 2002171A-4 |
| Rocap Test Requirement(s) | NO | Lubricant Requirements(s) | NO |
| Washer Inner Diameter(s) |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2020-03-24-8
DIME Test ID: 2020-03-24-8-2
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2020-04-15
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: bewing
Date of test: 04/15/2020
UTM: 400kip
Temperature: 72
| Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | UNC 3/4 | 0.334 | 45881 | 204 | 137367 | 127782 | 42679 | A193 B7 Stud |
General comments (publicly viewable) (Max 1000 characters): A193 B7 Stud
Test Graph
Source: Bluehill Data Point FileTest was verified on 4/15/2020 ✔