Summary for Test 2025-03-11-26-10
Test performed: ASTM D4791-10Project Information
| Project Identifiers | Project ID: 1000216 DEA: 081G6304 EFIS: 0816000043 COOP: NONE |
|---|---|
| DIST-CO-RTE-PM | 08-RIV-111-47.2/55.3 |
| Award Date | 09/05/2024 |
| Closeout Date | 01/21/2026 |
| Work Description | RHMA-G, REPLACE AC SURFACING, AND COLD PLANE AC PVMT. |
| Location Description | RIVERSIDE COUNTY IN PALM SPRINGS FROM GOLF CLUB DRIVE TO WEST GATEWAY DRIVE |
| QA Service Level | 1 (Verified on 05/15/2024) |
Sample Information
| Sample Taken Date | 03/11/2025 | Sample Unique Key | 26 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 03/12/2025 |
| Sample type | Verification | A brief description of the sample | PSUE 3/4" RHMA G SP 0.50% LAS |
| The quantity of what the sample constitutes | 3 bags of comb agg, 1 bag EA CRM (scrap and hi-nat) | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | Luke | Last name of sampler or witnessed by | Hall |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0163G-25 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Ingevity, CRM, SJR, Granite, VLO, West Coast Aggs | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-33-0072 |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | The fabricator/manufacturer designation for the sample | ||
| The plant number | A detailed description of where the material sample was collected | Belt cut at Granite Construction - Desert Hot Spring | |
| Where the material sample would have been placed if not sampled | Asphalt Paving | Primary Aggregate Nominal Size | 3/4 inch |
| The concrete mix design number | 1556 | Lot number | |
| Sublot number | Aggregate Mix Number |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2025-03-11-26
DIME Test ID: 2025-03-11-26-10
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Test Release Date: 2026-01-30
Test Results
Method A - Percentage of Flat Particles, Elongated Particles, and Flat & Elongated Particles
Method B - Flat & Elongated Particles
Method: B
Determination: By Mass
Dimensional ratio used: 5:1
Input Type: Calculated
Tester's full name: David Padilla
Date of test: 03/17/2025
Weighted percentage of particles (by mass) that were flat and elongated: 0 %
Weighted percentage of particles (by mass) that were not flat and elongated: 100 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 1/30/2026 ✔