Summary for Test 2025-03-04-20-6
Test performed: ASTM A370-20Project Information
| Project Identifiers | Project ID: 994525 DEA: 031H9904 EFIS: 0317000043 |
|---|---|
| DIST-CO-RTE-PM | 03-PLA,NEV-80-68.3/69.7,0.0/R2.7 |
| Award Date | 11/07/2023 |
| Closeout Date | Not set |
| Work Description | RDWY EXC, PLACE HMA & JPCP, SLAB REPLACEMENT & POLYESTER CONC OVERLAY. |
| Location Description | PLACER AND NEVADA COUNTIES NEAR KINGVALE FROM 0.3 MILE WEST OF TROY UNDERCROSSING TO 0.2 MILE EAST OF SODA SPRINGS OVERCROSSING |
| QA Service Level | 1 (Verified on 05/15/2023) |
Sample Information
| Sample Taken Date | 03/04/2025 | Sample Unique Key | 20 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | No | Date that the sample was received by the laboratory/organization performing the testing | 04/17/2025 |
| Sample type | Quality Assurance | A brief description of the sample | A36 ALL THREAD STUD |
| The quantity of what the sample constitutes | 28 | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | Chris | Last name of sampler or witnessed by | Dsouza |
| Title of sampler | Telephone number of sampler | 9493852715 | |
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | St Louis Screw and Bolt | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | B277-010-25 | Structure unique identifier | |
| Structure name | Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | |
|---|---|---|---|
| Heat Number(s) | 8000025424 1000121528 149479 | Nut Mfg. Lot Number(s) | W000145668 |
| Washer Mfg. Lot Number(s) | 149479 / 44306 | Bolt Specification | ASTM A36 |
| Bolt Length(s) | 4 1/2" | Nut Specification | A563 DH |
| Washer Specification | ASTM F436 | Finish | HDG |
| Diameter/Size | 5/8" | Bolt Mfg. Lot Number | J41513 |
| Rocap Test Requirement(s) | Lubricant Requirements(s) | ||
| Washer Inner Diameter(s) |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2025-03-04-20
DIME Test ID: 2025-03-04-20-6
Testing Lab: Atlas - Oakland
Test Method: ASTM A370-20: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Test Release Date: 2025-06-05
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Andrew Auvinen
Date of test: 06/03/2025
UTM: NA
Temperature: 72 f
| Num | Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By |
|---|---|---|---|---|---|---|---|---|
| 1 | 1A | 8000025424 | 0.625 | 0.226 | 81726 | 98451 | 0 | W Torres |
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 6/5/2025 ✔