Summary for Test 2019-07-09-7-9
Test performed: CTM 202-November 2011Project Information
| Project Identifiers | Project ID: 213647 DEA: 080N9724 EFIS: 0815000102 |
|---|---|
| DIST-CO-RTE-PM | 08-SBD-395-35.5/39.1 |
| Award Date | 12/03/2018 |
| Closeout Date | 12/02/2019 |
| Work Description | CONSTRUCT MEDIAN AND WIDENING SHOULDER |
| Location Description | SAN BERNARDINO COUNTY NEAR ADELANTO FROM 1.3 MILES SOUTH TO 2.3 MILES NORTH OF KRAMER ROAD |
| QA Service Level | 1 (Verified on 03/05/2019) |
Sample Information
| Sample Taken Date | 07/09/2019 | Sample Unique Key | 7 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 07/10/2019 |
| Sample type | Verification | A brief description of the sample | 1/2 HMA-A-SP R15 |
| The quantity of what the sample constitutes | PSE 14 bags | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | A S | Last name of sampler or witnessed by | SAMANO MAQUIBAN |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0410A-19 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Agcon Inc Oro Grande, Cemex White Mountain | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-36-0046, 91-36-0106 |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | 1/2 HMA-A-SP R15 | The fabricator/manufacturer designation for the sample | 300215 |
| The plant number | Unknown | A detailed description of where the material sample was collected | Belt Cut at Plant |
| Where the material sample would have been placed if not sampled | Unknown | Primary Aggregate Nominal Size | 1/2 inch |
| The concrete mix design number | Unknown | Lot number | Unknown |
| Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2019-07-09-7
DIME Test ID: 2019-07-09-7-9
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: CTM 202-November 2011: Method of Test for Sieve Analysis of Fine and Coarse Aggregates
Test Release Date: 2019-08-22
Test Results
What size aggregate is being tested?: Combined Gradation
Individual or cumulative mass retained on each sieve?: Cumulative Mass Retained
For Combined Gradation only, has the fine aggregate sample been reduced?: No
For Combined Gradation only, use #40 Sieve?: No
Input Type: Calculated
Tester's full name: Larry Diaz
Date of test: 07/12/2019
Cumulative percent passing the 3 in. sieve: 100 %
Cumulative percent passing the 2 1/2 in. sieve: 100 %
Cumulative percent passing the 2 in. sieve: 100 %
Cumulative percent passing the 1 1/2 in. sieve: 100 %
Cumulative percent passing the 1 in. sieve: 100 %
Cumulative percent passing the 3/4 in. sieve: 100 %
Cumulative percent passing the 1/2 in. sieve: 100 %
Cumulative percent passing the 3/8 in. sieve: 100 %
Cumulative percent passing the #4 sieve: 90 %
Cumulative percent passing the #8 sieve: 72 %
Cumulative percent passing the #16 sieve: 54 %
Cumulative percent passing the #30 sieve: 38 %
Cumulative percent passing the #50 sieve: 25 %
Cumulative percent passing the #100 sieve: 16 %
Cumulative percent passing the #200 sieve: 10 %
General comments (publicly viewable) (Max 1000 characters): RAP Gradation After Ignition Oven
Test was verified on 8/22/2019 ✔