Summary for Test 2018-01-11-2-1
Test performed: ASTM F606-14Project Information
| Project Identifiers | Project ID: 211669 DEA: 022C0904 EFIS: 0200000161 |
|---|---|
| DIST-CO-RTE-PM | 02-PLU-70-50.6/51.7 |
| Award Date | 11/16/2016 |
| Closeout Date | 11/12/2020 |
| Work Description | BRIDGE WIDENING AND DECK REPLACEMENT, HMA, MGS AND CULVERT REPLACEMENT |
| Location Description | PLUMAS COUNTY NEAR QUINCY FROM 0.6 MILE WEST TO 0.5 MILE EAST OF SPRING GARDEN BRIDGE OVERHEAD |
| QA Service Level | 1 (Verified on 10/25/2016) |
Sample Information
| Sample Taken Date | 01/11/2018 | Sample Unique Key | 2 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 01/11/2018 |
| Sample type | Quality Assurance | A brief description of the sample | A449 All thread |
| The quantity of what the sample constitutes | 206 | From where was the sample collected | Distributor |
| First name of sampler or witnessed by | Scott | Last name of sampler or witnessed by | Leavitt |
| Title of sampler | QA Inspector | Telephone number of sampler | 510 590-0116 |
| Laboratory sample identification | Unknown | Linked DIME Sample ID | Unknown |
| The fabricator/manufacturer/facility name | UIS | Transportation Laboratory (TL) Number | Unknown |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | S28-007-18 | Structure unique identifier | Not set |
| Structure name | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | N/A |
|---|---|---|---|
| Heat Number(s) | DL15105873 | Nut Mfg. Lot Number(s) | N/A |
| Washer Mfg. Lot Number(s) | N/A | Bolt Specification | A449 |
| Bolt Length(s) | 16" | Nut Specification | N/A |
| Washer Specification | N/A | Finish | HDG |
| Diameter/Size | 3/4 | Bolt Mfg. Lot Number | 29330 |
| Rocap Test Requirement(s) | No | Lubricant Requirements(s) | No |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2018-01-11-2
DIME Test ID: 2018-01-11-2-1
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2018-01-29
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Fred
Date of test: 01/22/2018
UTM: 400KIP
Temperature: 72
| Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 1A | A449 .75 x 16 Althreaded Stud | 0.334 | 43860 | 195 | 131317 | 116059 | 38764 | 449 Althread Stud |
General comments (publicly viewable) (Max 1000 characters): 449 Althread Stud
Test Graph
Source: Partner Data Point FileTest was verified on 1/22/2018 ✔