Summary for Test 2024-03-13-14-10
Test performed: AASHTO T30-19Project Information
Project Identifiers | Project ID: 994903 DEA: 11430244 EFIS: 1118000033 |
---|---|
DIST-CO-RTE-PM | 11-SD,-125-9.3/13.0 |
Award Date | 09/06/2023 |
Closeout Date | Not set |
Work Description | PLACE HMA, RHMA, SLAB REPLACEMENT, AND ELECTRICAL WORK. |
Location Description | SAN DIEGO COUNTY IN AND NEAR LEMON GROVE FROM 0.3 MILE SOUTH OF ELKELTON PLACE UNDERCROSSING TO 0.2 MILE SOUTH OF ROUTE 125/94 SEPARATION |
QA Service Level | 1 (Verified on 11/14/2023) |
Sample Information
Sample Taken Date | 03/13/2024 | Sample Unique Key | 14 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 03/14/2024 |
Sample type | Quality Assurance | A brief description of the sample | 1 1/2" HMA |
The quantity of what the sample constitutes | 3 bags | From where was the sample collected | Source |
First name of sampler or witnessed by | Ben | Last name of sampler or witnessed by | Smith |
Title of sampler | Telephone number of sampler | ||
Laboratory sample identification | 0108-JMF | Linked DIME Sample ID | 2024-03-13-12 |
The fabricator/manufacturer/facility name | Vulcan Otay | Transportation Laboratory (TL) Number | |
Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
Structure name |
Material Information
Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-37-0035 |
---|---|---|---|
The fabricator's/manufacturer's product name for the sample | The fabricator/manufacturer designation for the sample | ||
The plant number | A detailed description of where the material sample was collected | Plant | |
Where the material sample would have been placed if not sampled | Primary Aggregate Nominal Size | 1-1/2 inch | |
The concrete mix design number | Lot number | ||
Sublot number | Aggregate Mix Number |
Test Details
DIME Sample ID: 2024-03-13-14
DIME Test ID: 2024-03-13-14-10
Testing Lab: CT D11 - District 11 Materials Laboratory
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Test Release Date: 2024-03-25
Test Results
Does this test use 1/4 sieve?: No
Is an aggregate correction factor used?: No
Input Type: Measured
Tester's full name: Daniel Smith
Date of test: 03/19/2024
Cumulative Mass Retained | Cumulative Percent Passing | |||||
---|---|---|---|---|---|---|
1376.9 grams | ||||||
0.0 grams | 100 % | |||||
0.0 grams | 100 % | |||||
0.0 grams | 100 % | |||||
0.0 grams | 100 % | |||||
0.0 grams | 100 % | |||||
44.9 grams | 97 % | |||||
440.0 grams | 68 % | |||||
743.3 grams | 46 % | |||||
936.8 grams | 32 % | |||||
1075.7 grams | 22 % | |||||
1206.2 grams | 12 % | |||||
1302.9 grams | 5 % | |||||
1369.1 grams | 0.6 % |
General comments (publicly viewable) (Max 1000 characters): Complies
Test was verified on 3/25/2024 ✔