Summary for Test 2018-04-24-32-3
Test performed: ASTM F606-14aProject Information
Project Identifiers | Project ID: 213087 Permit Numbers: 0916NCS0245 0917NDP0279 0917NRW0191 |
---|---|
DIST-CO-RTE-PM | 09-KER-14-16.3/17.1 |
Award Date | 12/29/2016 |
Closeout Date | 06/23/2021 |
Work Description | Construct sidewalk, curb and gutter, as shown on the plans titled "Plans for Construction of Pedestrian Path Improvements on State Route 14 in Mojave, CA, Contract No. 16007" signed and stamped by Registered Civil Engineer Bryon A. Smith, RCE No. 61252.Notwithstanding General Provision #4, |
Location Description | Mojave, Mojave |
QA Service Level | 1 (Verified on 02/01/2018) |
Sample Information
Sample Taken Date | 04/24/2018 | Sample Unique Key | 32 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 05/01/2018 |
Sample type | Quality Assurance | A brief description of the sample | F1554 Gr 105 Anchor bolt assembly |
The quantity of what the sample constitutes | 1 | From where was the sample collected | Distributor |
First name of sampler or witnessed by | Dave | Last name of sampler or witnessed by | Flygare |
Title of sampler | QC and Safety assistant | Telephone number of sampler | Unknown |
Laboratory sample identification | Unknown | Linked DIME Sample ID | Unknown |
The fabricator/manufacturer/facility name | Ensco | Transportation Laboratory (TL) Number | C719150 |
Inspector Lot Number from the Transportation Laboratory (TL) Form | B76-078-18 | Structure unique identifier | Not set |
Structure name | Not set |
Material Information
Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | |
---|---|---|---|
Heat Number(s) | M42681, DL17101378, 175125, DL12102282 | Nut Mfg. Lot Number(s) | 393694A, DL1710137801, 325719B, DL1210228201 |
Washer Mfg. Lot Number(s) | 1017-672 | Bolt Specification | F1554 Gr105 |
Bolt Length(s) | 3'-4" | Nut Specification | A194 Gr2H |
Washer Specification | F436 | Finish | HDG |
Diameter/Size | 1" | Bolt Mfg. Lot Number | 78641 |
Rocap Test Requirement(s) | Lubricant Requirements(s) |
Test Details
DIME Sample ID: 2018-04-24-32
DIME Test ID: 2018-04-24-32-3
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Test Release Date: 2018-05-17
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Brian
Date of test: 05/03/2018
UTM: 400KIP
Temperature: 72 F
Num | Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By |
---|---|---|---|---|---|---|---|
1 | 2A | 325719B | 1-8 HEX | 108780 | 483.86 | Nut Proof | Brian |
General comments (publicly viewable) (Max 1000 characters): Nut Proof
Test Graph
Source: Partner Data Point FileTest was verified on 5/10/2018 ✔