Summary for Test 2017-06-02-14-1

Test performed: AASHTO T104-11

Project Information

Project IdentifiersProject ID: 211871
DEA: 022H3304
DIST-CO-RTE-PM02-LAS,MOD-395-119.0/128.7,39.9/61.6
Award DateNot set
Closeout Date10/25/2017
Work DescriptionASPHALT-RUBBER CHIP SEAL, REPLACE AC SURFACING, STRIPING
Location DescriptionLASSEN AND MODOC COUNTIES ON ROUTE 395 FROM 1.7 MILES SOUTH OF FILLMAN ROAD TO 0.4 MILE SOUTH OF ASH VALLEY ROAD AND FROM COUNTY ROAD 133A TO OREGON STATE LINE
QA Service Level1 (Verified on 07/27/2017)

Sample Information

Sample Taken Date06/02/2017 Sample Unique Key14
Will the laboratory/organization for which you are a member perform testing on this material sample?Yes Date that the sample was received by the laboratory/organization performing the testing06/02/2017
Sample typeVerification A brief description of the samplevirgin aggregate
The quantity of what the sample constitutesJMF From where was the sample collectedManufacturer
First name of sampler or witnessed byDave Last name of sampler or witnessed byLockett
Title of samplerTester Telephone number of samplerUnknown
Laboratory sample identificationD76964, 17-0222 Linked DIME Sample IDUnknown
The fabricator/manufacturer/facility nameEagle Peak Rock and Paving, Alturas, CA Transportation Laboratory (TL) Number852336
Inspector Lot Number from the Transportation Laboratory (TL) FormUnknown Structure unique identifierNot set
Structure nameNot set

Material Information

Material TypeJob Mix Formula Partial Source Identification (SMARA or name of Pit)91-25-0029
The fabricator's/manufacturer's product name for the sampleUnknown The fabricator/manufacturer designation for the sampleUnknown
The plant numberUnknown A detailed description of where the material sample was collectedstockpiles
Where the material sample would have been placed if not sampledJMF Superpave or Non-superpave MixSuperpave
JMF Verification ID

Test Details

DIME Sample ID: 2017-06-02-14
DIME Test ID: 2017-06-02-14-1
Testing Lab: CT HQ - Sacramento Aggregate Testing Laboratory
Test Method: AASHTO T104-11: Standard Method of Test for Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate (Soundness)
Test Release Date: 2017-08-14

Test Results


What size aggregate is being tested?: Fine Aggregate
Input Type: Calculated
Tester's full name: Benjamin Lenz
Date of test: 08/14/2017
What type of solution was used?: Sodium sulfate
What was the condition of the solution?: Previously used
Mass of sample retained on the #4 sieve (before immersion): no data
Mass of sample retained on the #4 sieve (before immersion): 0 grams
Mass of sample retained on the #8 sieve (before immersion): 100.1 grams
Mass of sample retained on the #16 sieve (before immersion): 100.1 grams
Mass of sample retained on the #30 sieve (before immersion): 100 grams
Mass of sample retained on the #50 sieve (before immersion): 100 grams
Percent loss from sample retained on the No. 4 x 8 sieve (fine):0 %
Percent loss from sample retained on the No. 8 x 16 sieve:4 %
Percent loss from sample retained on the No. 16 x 30 sieve:3 %
Percent loss from sample retained on the No. 30 x 50 sieve:2 %
Percent loss from sample retained on the #50 sieve:4 %
Fine weighted average loss:no data
General comments (publicly viewable) (Max 1000 characters): Weighted average for fine material is 3.2%

Test was verified on 8/14/2017