Summary for Test 2020-06-18-42-8
Test performed: AASHTO T312-14Project Information
| Project Identifiers | Project ID: 214571 DEA: 020J1104 EFIS: 0219000062 |
|---|---|
| DIST-CO-RTE-PM | 02-PLU-70-33.1/42.1 |
| Award Date | 02/07/2020 |
| Closeout Date | 04/27/2021 |
| Work Description | PLACE HMA & SHOULDER BACKING, & REMOVE & REPLACE PAVEMENT DELINEATION. |
| Location Description | PLUMAS COUNTY AT AND NEAR KEDDIE FROM INDIAN CREEK BRIDGE TO 0.3 MILE WEST OF SPANISH CREEK BRIDGE NO. 09-0018 |
| QA Service Level | 1 (Verified on 01/22/2020) |
Sample Information
| Sample Taken Date | 06/18/2020 | Sample Unique Key | 42 |
|---|---|---|---|
| Date that the sample was received by the laboratory/organization performing the testing | 06/18/2020 | Sample type | Verification |
| A brief description of the sample | 3/4-inch Type A HMA (PG 64-16) 15.0 RAP, 1.0 Lime | The quantity of what the sample constitutes | JMF Verification |
| From where was the sample collected | Manufacturer | First name of sampler or witnessed by | PEI |
| Last name of sampler or witnessed by | Joe | Title of sampler | |
| Telephone number of sampler | Laboratory sample identification | D78486 | |
| Linked DIME Sample ID | The fabricator/manufacturer/facility name | Sierra Cascade Aggregate and Asphalt Products | |
| Transportation Laboratory (TL) Number | 734736 | Inspector Lot Number from the Transportation Laboratory (TL) Form | |
| Structure unique identifier | Structure name | ||
| Bid Item | Not set |
Material Information
| Material Type | Hot Mix Asphalt | HMA Type | Type A HMA |
|---|---|---|---|
| HMA Grading | 3/4 inch | Lot number | |
| Sublot number | HMA Mix Number | Not set | |
| Binder content (%) | Not set | Virgin binder PG | Not set |
| Design binder PG | Not set | Binder Supplier | Not set |
| RAP content (%) | Not set | WMA Additives | Not set |
| Antistrip type | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2020-06-18-42
DIME Test ID: 2020-06-18-42-8
Testing Lab: CT D02 - Redding Northern Regional Laboratory
Test Method: AASHTO T312-14: Preparing and Determining the Density of Asphalt Mixture Specimens by Means of the Superpave Gyratory Compactor (Method of Compaction)
Test Release Date: 2020-10-05
Test Results
HMA Type: Type A HMA
Is this test used for JMF verification:
Input Type: Measured
Tester's full name: Terry McCormick
Date of test: 06/19/2020
Start time of test (military time): 0826
Specimen identification: 2061901
Percent Binder Content: 5.9 %
Average diameter of the mold: 150 mm
Height of the extruded specimen (Hm): 115.1 mm
Mass of the specimen: 4665.8 g
Maximum Specific Gravity (Gmm): 2.444
Bulk Specific Gravity (Gmb): 2.382
Unit weight of water: 1 g/cm^3
Gyration Angle: 1.16 deg
Gyration Angle: 20.2 mrad
Method used to verify gyration angle: AASHTO T 344 at room temperature
Uncorrected relative density (Gmmu8): 84.2 %
Uncorrected relative density (Gmmu85): 92.6 %
Uncorrected relative density (Gmmu130): 93.9 %
Air Voids (AV8): 12.6 %
Air Voids (AV85): 3.9 %
Air Voids (AV130): 2.5 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 10/5/2020 ✔