Summary for Test 2026-06-25-18-19
Test performed: ASTM F606-21Project Information
| Project Identifiers | Project ID: 1002102 DEA: 081P9904 EFIS: 0824000205 |
|---|---|
| DIST-CO-RTE-PM | 08-SBD-138-15.264 |
| Award Date | Not set |
| Closeout Date | Not set |
| Work Description | SIGNAL AND LIGHTING SYSTEM. CONSTRUCTION ON STATE HIGHWAY IN SAN BERNARDINO COUNTY NEAR HESPERIA AT ROUTE 15 SOUTHBOUND RAMPS AND AT ROUTE 15 NORTHBOUND RAMPS |
| Location Description | Not set |
| QA Service Level | 1 (Verified on 04/28/2026) |
Sample Information
| Sample Taken Date | 06/25/2026 | Sample Unique Key | 18 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 08/05/2026 |
| Sample type | Quality Assurance | A brief description of the sample | 2.25" x 42" Double End Studs |
| The quantity of what the sample constitutes | 400 | From where was the sample collected | Source |
| First name of sampler or witnessed by | Jayce | Last name of sampler or witnessed by | Groves |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | Halo | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | No |
|---|---|---|---|
| Heat Number(s) | 79018794, 21005610, 22520370 | Nut Mfg. Lot Number(s) | BZKS |
| Washer Mfg. Lot Number(s) | 419358 | Bolt Specification | F1554 GR55 |
| Bolt Length(s) | 42" | Nut Specification | A563 |
| Washer Specification | F436 | Finish | HDG |
| Diameter/Size | 2.25" | Bolt Mfg. Lot Number | 79018794 |
| Rocap Test Requirement(s) | No | Lubricant Requirements(s) | No |
| Washer Inner Diameter(s) | TWO ONE QUARTER |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2026-06-25-18
DIME Test ID: 2026-06-25-18-19
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Test Release Date: 2026-08-18
Test Results
Number of Bolt Samples: 2
Input Type: Measured
Tester's full name: Andrew Auvinen
Date of test: 08/14/2026
UTM: NA
Temperature: 0 f
| Num | Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Wedge Angle (deg) | Comments | Tested By |
|---|---|---|---|---|---|---|---|---|
| 1 | 1A | 79018794 | 2.25 | 301280 | 0 | 0 | Yield 212480 | Kleinfelder |
| 2 | 1B | 79018794 | 2.25 | 289250 | 0 | 0 | Yield 204120 | Kleinfelder |
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 8/18/2026 ✔