DIME - Test Summary

Summary for Test 2018-02-27-15-2

Test performed: CTM 214-August 2010

Project Identifiers	Project ID: 212679 DEA: 023E7204 EFIS: 0200020154
DIST-CO-RTE-PM	02-TEH-36-42.1/46.0
Award Date	12/18/2017
Closeout Date	08/07/2019
Work Description	COLD PLANING, PAVING, MINOR CONCRETE, ELECTRICAL AND STRIPING WORK.
Location Description	TEHAMA COUNTY IN AND NEAR RED BLUFF FROM EAST SAND SLOUGH BRIDGE TO 0.6 MILE EAST OF STICE ROAD
QA Service Level	1 (Verified on 05/24/2018)

Sample Taken Date	02/27/2018	Sample Unique Key	15
Will the laboratory/organization for which you are a member perform testing on this material sample?	Yes	Date that the sample was received by the laboratory/organization performing the testing	02/27/2018
Sample type	Verification	A brief description of the sample	5/8 inch Untreated Aggregate
The quantity of what the sample constitutes	JMF	From where was the sample collected	Manufacturer
First name of sampler or witnessed by	Cheryl	Last name of sampler or witnessed by	Abraham
Title of sampler	Unknown	Telephone number of sampler	Unknown
Laboratory sample identification	D77292A	Linked DIME Sample ID	Unknown
The fabricator/manufacturer/facility name	Tullis, Inc - Northstate Asphalt - Redding, CA	Transportation Laboratory (TL) Number	852088
Inspector Lot Number from the Transportation Laboratory (TL) Form	Unknown	Structure unique identifier	Not set
Structure name	Not set

Material Type	Aggregate	Source Identification (SMARA, name of Pit or Job Site)	91-45-0057::SHASTA RANCH AGGREGATES
The fabricator's/manufacturer's product name for the sample	Unknown	The fabricator/manufacturer designation for the sample	Unknown
The plant number	Unknown	A detailed description of where the material sample was collected	Stockpile @ Plant
Where the material sample would have been placed if not sampled	Unknown	Primary Aggregate Nominal Size	3/4 inch
The concrete mix design number	Unknown	Lot number	Not set
Sublot number	Not set	Aggregate Mix Number	Not set
HMA Pay	No

DIME Sample ID: 2018-02-27-15

DIME Test ID: 2018-02-27-15-2

Testing Lab: CT HQ - Sacramento Aggregate Testing Laboratory

Test Method: CTM 214-August 2010: Method of Test for Soundness of Aggregates by Use of Sodium Sulfate

Test Release Date: 2018-04-13

What size aggregate is being tested?: Coarse Aggregate

Input Type: Calculated

Tester's full name: Benjamin Lenz

Date of test: 04/13/2018

Percentage Loss of material retained on 2 x 1 ½ in. sieve: no data

Percentage Loss of material retained on 1 ½ x 1 in. sieve: no data

Percentage Loss of material retained on 1 x ¾ in. sieve: no data

Percentage Loss of material retained on ¾ x ½ in. sieve: no data

Percentage Loss of material retained on ½ x ⅜ in. sieve: no data

Percentage Loss of material retained on ⅜ in. x #4 sieve: no data

Percentage Loss of material retained on 2 in. through 1 1/2 in. sieve: no data

Percentage Loss of material retained on 1 in. through 3/4 in. sieve: no data

Percentage Loss of material retained on 3/4 in. through #4 sieve: no data

Weighted Average Percent Loss of Coarse Aggregate: 1 %

Batch Soundness Loss of Coarse Aggregate (2 1/2 in maximum): no data

Batch Soundness Loss of Coarse Aggregate (1 1/2 in maximum): no data

General comments (publicly viewable) (Max 1000 characters):

Test was verified on 4/13/2018 ✔