Summary for Test 2026-03-12-31-20
Test performed: AASHTO T30-19Project Information
| Project Identifiers | Project ID: 995065 DEA: 112N1764 |
|---|---|
| DIST-CO-RTE-PM | 11-IMP-8-R50.3/R96.7 |
| Award Date | 05/01/2025 |
| Closeout Date | Not set |
| Work Description | MICROSURFACING, SHOULDER BACKING, PAVEMENT MARKING, & INSTALL SIGNS. |
| Location Description | IMPERIAL COUNTY AT VARIOUS LOCATIONS FROM 0.2 MILE WEST OF BONDS CORNER OVERCROSSING TO 0.2 MILE EAST OF FOURTH AVENUE OVERCROSSING . |
| QA Service Level | 1 (Verified on 06/11/2024) |
Sample Information
| Sample Taken Date | 03/12/2026 | Sample Unique Key | 31 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 03/13/2026 |
| Sample type | Verification | A brief description of the sample | JMFR |
| The quantity of what the sample constitutes | 5 bags | From where was the sample collected | Supplier |
| First name of sampler or witnessed by | Gerardo | Last name of sampler or witnessed by | Cordero |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | API Gateway | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | See Mix |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | The fabricator/manufacturer designation for the sample | ||
| The plant number | A detailed description of where the material sample was collected | Plant | |
| Where the material sample would have been placed if not sampled | Primary Aggregate Nominal Size | 3/4 inch | |
| The concrete mix design number | Lot number | ||
| Sublot number | Aggregate Mix Number | 40 API Val |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2026-03-12-31
DIME Test ID: 2026-03-12-31-20
Testing Lab: CT D11 - District 11 Materials Laboratory
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Test Release Date: 2026-04-07
Test Results
Does this test use 1/4 sieve?: No
Is an aggregate correction factor used?: Yes
Input Type: Measured
Tester's full name: Shawn Rivers
Date of test: 04/01/2026
| Cumulative Mass Retained | Correction Factor | Cumulative Percent Passing | ||||
|---|---|---|---|---|---|---|
| 1897.6 grams | ||||||
| 0.0 grams | 0.0 % | 100 % | ||||
| 0.0 grams | 0.0 % | 100 % | ||||
| 0.0 grams | 0.0 % | 100 % | ||||
| 93.6 grams | 0.5 % | 96 % | ||||
| 240.4 grams | -1.0 % | 86 % | ||||
| 543.0 grams | -4.5 % | 67 % | ||||
| 1348.8 grams | -5.0 % | 24 % | ||||
| 1620.8 grams | -4.5 % | 10 % | ||||
| 1704.5 grams | 0.0 % | 10 % | ||||
| 1764.2 grams | -2.5 % | 5 % | ||||
| 1811.3 grams | -1.5 % | 3 % | ||||
| 1843.0 grams | -1.5 % | 1 % | ||||
| 1860.8 grams | -0.6 % | 1.3 % | ||||
| 1864.0 grams | ||||||
General comments (publicly viewable) (Max 1000 characters): Oven 3
Complies
Test was verified on 4/7/2026 ✔