Summary for Test 2025-11-17-3-3
Test performed: ASTM F606-21Project Information
| Project Identifiers | Project ID: 1000402 DEA: 11430384 EFIS: 1118000114 |
|---|---|
| DIST-CO-RTE-PM | 11-SD-805-23.7/28.5 |
| Award Date | 10/09/2024 |
| Closeout Date | Not set |
| Work Description | REPLACE DRAINAGE, CONCRETE PAVEMENT, AND MODIFY ELECTRICAL SYSTEMS. |
| Location Description | SAN DIEGO COUNTY IN SAN DIEGO FROM 0.1 MILE NORTH OF ROUTE 805/52 SEPARATION TO ROUTE 5/805 SEPARATION |
| QA Service Level | 1 (Verified on 11/18/2024) |
Sample Information
| Sample Taken Date | 11/17/2025 | Sample Unique Key | 3 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | No | Date that the sample was received by the laboratory/organization performing the testing | 11/20/2025 |
| Sample type | Quality Assurance | A brief description of the sample | 3/4" x 2" A325 HDG |
| The quantity of what the sample constitutes | 4 Bolts | From where was the sample collected | Distributor |
| First name of sampler or witnessed by | Jacob Garcia | Last name of sampler or witnessed by | Garcia |
| Title of sampler | QA Inspector | Telephone number of sampler | 7606866753 |
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | Ababa Bolt | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | L169-074-25 | Structure unique identifier | |
| Structure name | Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | N/A |
|---|---|---|---|
| Heat Number(s) | MT217 | Nut Mfg. Lot Number(s) | |
| Washer Mfg. Lot Number(s) | Bolt Specification | ASTM A325 | |
| Bolt Length(s) | 2" | Nut Specification | N/A |
| Washer Specification | N/A | Finish | ASTM A153/F2329 |
| Diameter/Size | 3/4" | Bolt Mfg. Lot Number | 1333825-001-002, B2341961G1 |
| Rocap Test Requirement(s) | Lubricant Requirements(s) | ||
| Washer Inner Diameter(s) |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2025-11-17-3
DIME Test ID: 2025-11-17-3-3
Testing Lab: Kleinfelder - Rancho Cordova
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Test Release Date: 2025-12-09
Test Results
Number of Bolt Samples: 1
Input Type: Measured
Tester's full name: Andrew Auvinen
Date of test: 12/01/2025
UTM: NA
Temperature: 0 f
| Num | Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Wedge Angle (deg) | Comments | Tested By |
|---|---|---|---|---|---|---|---|---|
| 1 | 1A | B2341961G1 | 0.75 | 46190 | 0 | 0 | NA | Atlas |
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 12/9/2025 ✔