DIME - Test Summary

Summary for Test 2025-09-09-30-2

Test performed: ASTM C136-19

Project Identifiers	Project ID: 1000561 DEA: 010J8904 EFIS: 0119000119
DIST-CO-RTE-PM	01-HUM-36-3.9/6.0
Award Date	12/06/2024
Closeout Date	Not set
Work Description	HOT MIX ASPHALT, AGGREGATE BASE, AND STRUCTURAL CONCRETE.
Location Description	HUMBOLDT COUNTY AT CARLOTTA FROM 0.2 MILE WEST OF FISHER ROAD TO 0.2 MILE WEST OF WILDER ROAD
QA Service Level	1 (Verified on 09/23/2024)

Sample Taken Date	09/09/2025	Sample Unique Key	30
Will the laboratory/organization for which you are a member perform testing on this material sample?	Yes	Date that the sample was received by the laboratory/organization performing the testing	09/09/2025
Sample type	Quality Control	A brief description of the sample	1 Bucket of 1/2", 1 Bucket of 3/8", One Bucket of Sand
The quantity of what the sample constitutes	1 Bucket of 1/2", 1 Bucket of 3/8", One Bucket of Sand	From where was the sample collected	Source
First name of sampler or witnessed by	Patrick	Last name of sampler or witnessed by	Baddu
Title of sampler		Telephone number of sampler
Laboratory sample identification		Linked DIME Sample ID
The fabricator/manufacturer/facility name	ConFab Lathrop	Transportation Laboratory (TL) Number
Inspector Lot Number from the Transportation Laboratory (TL) Form		Structure unique identifier
Structure name		Bid Item	Not set

Material Type	Aggregate	Source Identification (SMARA, name of Pit or Job Site)	Confab California Lathrop
The fabricator's/manufacturer's product name for the sample		The fabricator/manufacturer designation for the sample
The plant number		A detailed description of where the material sample was collected	Plant Stockpile
Where the material sample would have been placed if not sampled		Primary Aggregate Nominal Size	1/2 inch
The concrete mix design number	VER90LV	Lot number
Sublot number		Aggregate Mix Number

DIME Sample ID: 2025-09-09-30

DIME Test ID: 2025-09-09-30-2

Testing Lab: Con-Fab California Corporation - Lathrop

Test Method: ASTM C136-19: Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates

Test Release Date: 2025-09-10

What type of gradation is being tested?: Combined Gradation

Individual or cumulative mass retained on each sieve?: Cumulative Mass Retained

Has the fine aggregate sample been reduced? (question for combined gradation type): Yes

Input Type: Calculated

Tester's full name: Patrick Baddu

Date of test: 09/09/2025

Cumulative percent passing the 2 in. sieve: 100 %

Cumulative percent passing the 1 1/2 in. sieve: 100 %

Cumulative percent passing the 1 in. sieve: 100 %

Cumulative percent passing the 3/4 in. sieve: 100 %

Cumulative percent passing the 1/2 in. sieve: 95.1 %

Cumulative percent passing the 3/8 in. sieve: 79.1 %

Cumulative percent passing the #4 sieve: 49.9 %

Cumulative percent passing the #8 sieve: 40.8 %

Cumulative percent passing the #16 sieve: 27.8 %

Cumulative percent passing the #30 sieve: 18 %

Cumulative percent passing the #50 sieve: 9.7 %

Cumulative percent passing the #100 sieve: 2.9 %

Cumulative percent passing the #200 sieve: 0.4 %

General comments (publicly viewable) (Max 1000 characters):

Test was verified on 9/10/2025 ✔