Summary for Test 2025-04-28-5-5
Test performed: ASTM F606-21Project Information
| Project Identifiers | Project ID: 994358 DEA: 033J3304 EFIS: 0322000251 |
|---|---|
| DIST-CO-RTE-PM | 03-SAC-12-0/0.5 |
| Award Date | Not set |
| Closeout Date | Not set |
| Work Description | MMBN Project. Replace backup drive system, replace lift span deck, install hydraulic barrier system and new generator, replace electrical control system, install new traffic gates and elevators, traffic control, |
| Location Description | Not set |
| QA Service Level | 1 (Verified on 10/25/2022) |
Sample Information
| Sample Taken Date | 04/28/2025 | Sample Unique Key | 5 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | No | Date that the sample was received by the laboratory/organization performing the testing | 05/05/2025 |
| Sample type | Quality Assurance | A brief description of the sample | 7/8-9 x 2 ½ |
| The quantity of what the sample constitutes | 2 | From where was the sample collected | Supplier |
| First name of sampler or witnessed by | Daniel | Last name of sampler or witnessed by | Garcia Arreola |
| Title of sampler | AMR | Telephone number of sampler | |
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | XKT Engineering | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | E367S1R |
|---|---|---|---|
| Heat Number(s) | 10917500 8000030539 240419 | Nut Mfg. Lot Number(s) | W000195536 |
| Washer Mfg. Lot Number(s) | E7373 | Bolt Specification | ASTM F3125 A325: 7/8”-9 x 2(1/2)” |
| Bolt Length(s) | 2-1/2 | Nut Specification | 7/8-9 Gr DH HVY HEX HOT DIP ASTM A563 |
| Washer Specification | 7/8” Hot DIP ASTM F436 | Finish | Plain |
| Diameter/Size | 7/8" | Bolt Mfg. Lot Number | E367S1 |
| Rocap Test Requirement(s) | Lubricant Requirements(s) | ||
| Washer Inner Diameter(s) |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2025-04-28-5
DIME Test ID: 2025-04-28-5-5
Testing Lab: Atlas - Oakland
Test Method: ASTM F606-21: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Test Release Date: 2025-06-05
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Andrew Auvinen
Date of test: 06/03/2025
UTM: NA
Temperature: 72 f
| Num | Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By |
|---|---|---|---|---|---|---|---|
| 1 | 1A | E367S1 | 0.875 | 64390 | 0 | NA | W Torres |
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 6/5/2025 ✔