Summary for Test 2024-06-21-52-4
Test performed: AASHTO T308-10Project Information
| Project Identifiers | Project ID: 994686 DEA: 051K4604 EFIS: 0518000210 |
|---|---|
| DIST-CO-RTE-PM | 05-SLO-46-29.7/32.2 |
| Award Date | 09/01/2023 |
| Closeout Date | 04/01/2025 |
| Work Description | COLD PLANE, PLACE HMA, RHMA, CONC PVMT, MODIFY SIGNAL AND LIGHTING. |
| Location Description | SAN LUIS OBISPO COUNTY IN PASO ROBLES FROM 300 FEET WEST OF ROUTE 101/46 SEPARATION TO 0.1 MILE EAST OF AIRPORT ROAD |
| QA Service Level | 1 (Verified on 04/18/2023) |
Sample Information
| Sample Taken Date | 06/21/2024 | Sample Unique Key | 52 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 06/20/2024 |
| Sample type | Dispute Resolution | A brief description of the sample | 1/2" RHMA-G |
| The quantity of what the sample constitutes | Four boxes of mix, 2 quart cans, and 2 bags of agg. | From where was the sample collected | Job Site |
| First name of sampler or witnessed by | Isaac | Last name of sampler or witnessed by | Larey-Chezem |
| Title of sampler | TET | Telephone number of sampler | (209) 610-9363 |
| Laboratory sample identification | 024-037 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | SPM-Templeton | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | Hot Mix Asphalt | HMA Type | RHMA-G |
|---|---|---|---|
| HMA Grading | 1/2 inch | Lot number | 1 |
| Sublot number | 7 | HMA Mix Number | |
| Binder content (%) | Not set | Virgin binder PG | Not set |
| Design binder PG | Not set | Binder Supplier | Not set |
| RAP content (%) | Not set | WMA Additives | Not set |
| Antistrip type | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2024-06-21-52
DIME Test ID: 2024-06-21-52-4
Testing Lab: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Test Release Date: 2024-06-27
Test Results
What temperature unit is used?: Celsius
Input Type: Measured
Tester's full name: James Brewster
Date of test: 06/26/2024
Test procedure used?: Method A
Mass of the specimen basket assembly: 4239.0 g
Mass of the specimen and specimen basket assembly prior to ignition: 5838.9 g
Mass of HMA Sample prior to ignition: 1599.9 g
Mass Loss: 142.2 g
Mass of aggregate remaining after ignition: 1457.7 g
Correction Factor (Percent by mass of HMA Specimen): 1.01 %
Moisture Content: 0.01 %
Temperature Compensation Factor: 0.22 %
Test Temperature: 538 C
Corrected Asphalt Binder Content: 7.65 %
General comments (publicly viewable) (Max 1000 characters): AASHTO T 308 section A2.8.1 If the asphalt binder correction factor exceeds 1.0 percent, the test temperature should be lowered. It did not exceed over 1.0%. therefore, we did not lower the temperature.
Test was verified on 6/27/2024 ✔