Summary for Test 2017-06-20-3-10
Test performed: ASTM F606-14Project Information
| Project Identifiers | Project ID: 211588 DEA: 030F3104 EFIS: 0300000078 |
|---|---|
| DIST-CO-RTE-PM | 03-ED-49-23.6/24.5 |
| Award Date | 12/12/2016 |
| Closeout Date | 01/08/2019 |
| Work Description | REPLACE BRIDGE. |
| Location Description | EL DORADO COUNTY NEAR COLOMA FROM 0.1 MILE EAST OF MARSHALL ROAD TO 0.3 MILE EAST OF LOTUS ROAD |
| QA Service Level | 1 (Verified on 10/19/2016) |
Sample Information
| Sample Taken Date | 06/20/2017 | Sample Unique Key | 3 |
|---|---|---|---|
| Date that the sample was received by the laboratory/organization performing the testing | 06/20/2017 | Sample type | Verification |
| A brief description of the sample | 3/4 x 5 1/2 A325 bolt,nut,washer | The quantity of what the sample constitutes | 9 and 12 |
| From where was the sample collected | Fabricator | First name of sampler or witnessed by | David |
| Last name of sampler or witnessed by | Flygare | Title of sampler | CA METS QA Inspector |
| Telephone number of sampler | (801) 669-2984 | Laboratory sample identification | Unknown |
| Linked DIME Sample ID | Unknown | The fabricator/manufacturer/facility name | UIS |
| Transportation Laboratory (TL) Number | Unknown | Inspector Lot Number from the Transportation Laboratory (TL) Form | B76-063-17 |
| Structure unique identifier | Not set | Structure name | Not set |
| Bid Item | Not set |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | n/a |
|---|---|---|---|
| Heat Number(s) | Bolt NF16100930, nut 20388020, FW 542102 | Nut Mfg. Lot Number(s) | Decker 15-40-006 |
| Washer Mfg. Lot Number(s) | D2020 | Bolt Specification | A325 |
| Bolt Length(s) | 5 1/2" | Nut Specification | A563-DH |
| Washer Specification | F436 | Finish | HDG |
| Diameter/Size | 3/4" x 5 1/2" | Bolt Mfg. Lot Number | G8505 |
| Rocap Test Requirement(s) | none | Lubricant Requirements(s) | |
| Washer Inner Diameter(s) | Bolt Mill Supplier | Not set | |
| Nut Mill Supplier | Not set | Washer Mill Supplier | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2017-06-20-3
DIME Test ID: 2017-06-20-3-10
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2017-07-05
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Brian
Date of test: 06/28/2017
UTM: 400KIP
Temperature: 71
| Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 1C | A449 7/8\" x 28\" Bolt 10 Deg Wedge | 0.462 | 61887 | 275 | 133955 | 126627 | 58502 | A449 Headed Bolt w/10 Degree Wedge |
General comments (publicly viewable) (Max 1000 characters): A449 Headed Bolt w/10 Degree Wedge
Test Graph
Source: Partner Data Point FileTest was verified on 6/28/2017 ✔