Summary for Test 2024-04-07-5-10
Test performed: AASHTO T30-19Project Information
| Project Identifiers | Project ID: 994612 DEA: 112N1414 EFIS: 1121000253 |
|---|---|
| DIST-CO-RTE-PM | 11-SD-15,78-Various |
| Award Date | 05/26/2023 |
| Closeout Date | Not set |
| Work Description | PLACE METHACRYLATE, POLYESTER CONCRETE, JOINT SEALS AND REPAIR SPALLS. |
| Location Description | SAN DIEGO COUNTY AT VARIOUS LOCATIONS |
| QA Service Level | 1 (Verified on 08/22/2023) |
Sample Information
| Sample Taken Date | 04/07/2024 | Sample Unique Key | 5 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 04/08/2024 |
| Sample type | Quality Assurance | A brief description of the sample | PSU |
| The quantity of what the sample constitutes | 3 bags | From where was the sample collected | Source |
| First name of sampler or witnessed by | Ben | Last name of sampler or witnessed by | Smith |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0401-PSU | Linked DIME Sample ID | 2024-04-07-4 |
| The fabricator/manufacturer/facility name | Martin Marietta | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | N/A |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | The fabricator/manufacturer designation for the sample | ||
| The plant number | A detailed description of where the material sample was collected | Plant | |
| Where the material sample would have been placed if not sampled | Primary Aggregate Nominal Size | 1/2 inch | |
| The concrete mix design number | Lot number | ||
| Sublot number | Aggregate Mix Number |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2024-04-07-5
DIME Test ID: 2024-04-07-5-10
Testing Lab: CT D11 - District 11 Materials Laboratory
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Test Release Date: 2024-04-22
Test Results
Does this test use 1/4 sieve?: No
Is an aggregate correction factor used?: No
Input Type: Measured
Tester's full name: Joseph Seymour
Date of test: 04/11/2024
| Cumulative Mass Retained | Cumulative Percent Passing | |||||
|---|---|---|---|---|---|---|
| 1482.6 grams | ||||||
| 0.0 grams | 100 % | |||||
| 0.0 grams | 100 % | |||||
| 0.0 grams | 100 % | |||||
| 0.0 grams | 100 % | |||||
| 0.0 grams | 100 % | |||||
| 0.0 grams | 100 % | |||||
| 541.8 grams | 63 % | |||||
| 778.4 grams | 47 % | |||||
| 948.4 grams | 36 % | |||||
| 1081.3 grams | 27 % | |||||
| 1200.6 grams | 19 % | |||||
| 1286.7 grams | 13 % | |||||
| 1342.2 grams | 9.5 % | |||||
General comments (publicly viewable) (Max 1000 characters): Rap T-30
Test was verified on 4/22/2024 ✔