DIME - Test Summary

Summary for Test 2023-11-20-67-1

Test performed: CTM 524-March 2013

Project Identifiers	Project ID: 993387 DEA: 07323404 EFIS: 0716000064
DIST-CO-RTE-PM	07-LA-5-R59.5/R67.9
Award Date	Not set
Closeout Date	Not set
Work Description	PLACE CULVERT, REPLACE DRAINAGE SYSTEM, RECONST ROADWAY & EMBANKMENT.
Location Description	LOS ANGELES COUNTY AT VARIOUS LOCATIONS FROM LAKE HUGHES ROAD UNDERCROSSING TO 1.9 MILES NORTH OF TEMPLIN HIGHWAY UNDERCROSSING
QA Service Level	1 (Verified on 12/06/2021)

Sample Taken Date	11/20/2023	Sample Unique Key	67
Will the laboratory/organization for which you are a member perform testing on this material sample?	Yes	Date that the sample was received by the laboratory/organization performing the testing	11/20/2023
Sample type	Quality Assurance	A brief description of the sample	Concrete beams
The quantity of what the sample constitutes	10 cubic yards	From where was the sample collected	Job Site
First name of sampler or witnessed by	Dominic	Last name of sampler or witnessed by	Montemayor
Title of sampler		Telephone number of sampler
Laboratory sample identification	23-2062	Linked DIME Sample ID
The fabricator/manufacturer/facility name	N/A	Transportation Laboratory (TL) Number
Inspector Lot Number from the Transportation Laboratory (TL) Form		Structure unique identifier
Structure name

Material Type	Concrete	The concrete mix design number	G3-21-CTS-220
The truck number from where the sample was collected		The batch plant ticket number from where the sample was collected	1
Concrete batch plant		The fabricator/manufacturer designation for the sample
A detailed description of where the material sample was collected	wheelbarrow	Where the material sample would have been placed if not sampled
From Lot No.		Bag Lot No.

DIME Sample ID: 2023-11-20-67

DIME Test ID: 2023-11-20-67-1

Testing Lab: Alta Vista Solutions - Whittier

Test Method: CTM 524-March 2013: Method of Test for Flexural Strength Of Rapid Strength Concrete

Test Release Date: 2024-02-27

Number of specimens: 3

Does the testing machine measure load or stress on the beam specimen?: Load

Fracture initiates in the tension surface: Within the Middle Third of the Span Length

Fracture occurred at a capped section: No

Is a beam dimensional correction factor used?: No

Input Type: Measured

Tester's full name: SoCal Reports

Date of test: 11/30/2023

Identification number: 23-2062

Width of specimen: 6.125 inch

Width of specimen 2: 6.0625 inch

Width of specimen 3: 6.0625 inch

Depth of specimen: 6.0625 inch

Depth of specimen 2: 6.125 inch

Depth of specimen 3: 6 inch

Span length of specimen: 18 inch

Span length of specimen 2: 18 inch

Span length of specimen 3: 18 inch

Maximum load applied: 570 lb

Maximum load applied 2: 585 lb

Maximum load applied 3: 585 lb

Curing history and apparent moisture condition of the specimen: Sand

If specimen was capped, ground or if leather shims were used: No

Defects in specimen, including numbers of beams discarded during test: No

Age of specimen: 10 days

Age of specimen in hours: no data

Modulus of rupture: 50 psi

Modulus of rupture 2: 50 psi

Modulus of rupture 3: 50 psi

Modulus of rupture average: 50 psi

General comments (publicly viewable) (Max 1000 characters):

Test was verified on 2/27/2024 ✔