Summary for Test 2021-06-14-43-5
Test performed: CTM 211-May 2010Project Information
| Project Identifiers | Project ID: 215250 DEA: 021J4404 EFIS: 0220000079 |
|---|---|
| DIST-CO-RTE-PM | 02-MOD-299-20.0/23.1,23.5/24.5,33.5/37.5 |
| Award Date | 12/14/2020 |
| Closeout Date | 09/27/2021 |
| Work Description | ASPHALT RUBBER CHIP SEAL. |
| Location Description | MODOC COUNTY AT VARIOUS LOCATIONS FROM 1.8 MILES WEST OF ROUTE 139 TO 0.3 MILE WEST OF RATTLESNAKE CREEK BRIDGE |
| QA Service Level | 1 (Verified on 10/30/2020) |
Sample Information
| Sample Taken Date | 06/14/2021 | Sample Unique Key | 43 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 06/22/2021 |
| Sample type | Department Acceptance | A brief description of the sample | 1 bag of Uncoated 3/8″ Aggregate for use in ARB Chip Seal |
| The quantity of what the sample constitutes | 1/2 day to whole project | From where was the sample collected | Other |
| First name of sampler or witnessed by | Cindy | Last name of sampler or witnessed by | Bryant |
| Title of sampler | TET | Telephone number of sampler | |
| Laboratory sample identification | D78852 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Eagle Peak Rock and Paving, Alturas, CA | Transportation Laboratory (TL) Number | 853350 |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name | Bid Item | Not set |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | Eagle Peak |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | Unknown | The fabricator/manufacturer designation for the sample | Unknown |
| The plant number | Unknown | A detailed description of where the material sample was collected | Unknown |
| Where the material sample would have been placed if not sampled | 02 MOD 299 | Primary Aggregate Nominal Size | 1/2 inch |
| The concrete mix design number | Not Applicable | Lot number | Unknown |
| Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2021-06-14-43
DIME Test ID: 2021-06-14-43-5
Testing Lab: CT D02 - Redding Northern Regional Laboratory
Test Method: CTM 211-May 2010: Abrasion of Coarse Aggregate by Use of the Los Angeles Abrasion Testing Machine
Test Release Date: 2022-01-28
Test Results
How many revolutions are required?: Both Tests
Input Type: Measured
Tester's full name: Dennis Hickey
Date of test: 06/23/2021
Grading: C
Mass of sample: 5000 grams
Mass retained No. 4 sieve (100 Rev Test): 0 grams
Mass retained No. 12 sieve (100 Rev Test): 4833 grams
Mass retained No. 4 sieve (500 Rev Test): 0 grams
Mass retained No. 12 sieve (500 Rev Test): 4218 grams
Percent wear (100 Rev Test): 3 %
Percent wear (500 Rev Test): 16 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 1/28/2022 ✔