Summary for Test 2021-06-15-32-4
Test performed: CTM 211-May 2010Project Information
| Project Identifiers | Project ID: 215441 DEA: 021J5204 EFIS: 0220000087 |
|---|---|
| DIST-CO-RTE-PM | 02-MOD,SIS-139-34.0/50.7,0.0/5.0 |
| Award Date | 03/02/2021 |
| Closeout Date | 09/27/2021 |
| Work Description | PLACE ASPHALT RUBBER BINDER CHIP SEAL & REPLACE AC SURFACING. |
| Location Description | MODOC AND SISKIYOU COUNTIES AT AND NEAR NEWELL FROM 3.3 MILES NORTH OF PEREZ OVERHEAD TO ROUTE 161 |
| QA Service Level | 1 (Verified on 02/01/2021) |
Sample Information
| Sample Taken Date | 06/15/2021 | Sample Unique Key | 32 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 06/16/2021 |
| Sample type | Department Acceptance | A brief description of the sample | 2 bags of Uncoated 3/8″ Aggregate for Use in ARB Chip Seal |
| The quantity of what the sample constitutes | One-half day to whole project | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | John | Last name of sampler or witnessed by | Carmichael |
| Title of sampler | Consultant | Telephone number of sampler | |
| Laboratory sample identification | D78845 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Hat Creek Construction and Materials - Shaw Pit - Lookout, CA | Transportation Laboratory (TL) Number | 990927 |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-25-0008::Shaw Pit |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | Unknown | The fabricator/manufacturer designation for the sample | Unknown |
| The plant number | Unknown | A detailed description of where the material sample was collected | Sampling Device at Plant |
| Where the material sample would have been placed if not sampled | Primary Aggregate Nominal Size | 1/2 inch | |
| The concrete mix design number | Lot number | Unknown | |
| Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2021-06-15-32
DIME Test ID: 2021-06-15-32-4
Testing Lab: CT D02 - Redding Northern Regional Laboratory
Test Method: CTM 211-May 2010: Abrasion of Coarse Aggregate by Use of the Los Angeles Abrasion Testing Machine
Test Release Date: 2022-01-11
Test Results
How many revolutions are required?: Both Tests
Input Type: Measured
Tester's full name: Terry McCormick
Date of test: 06/17/2021
Grading: C
Mass of sample: 4879 grams
Mass retained No. 4 sieve (100 Rev Test): 0 grams
Mass retained No. 12 sieve (100 Rev Test): 4735 grams
Mass retained No. 4 sieve (500 Rev Test): 0 grams
Mass retained No. 12 sieve (500 Rev Test): 4165 grams
Percent wear (100 Rev Test): 3 %
Percent wear (500 Rev Test): 15 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 1/11/2022 ✔