DIME - Test Summary

Summary for Test 2020-12-08-11-3

Test performed: CTM 202-November 2011

Project Identifiers	Project ID: 214921 DEA: 09367404 EFIS: 0916000025
DIST-CO-RTE-PM	09-KER-14-R4.7/R12.6
Award Date	Not set
Closeout Date	01/23/2023
Work Description	CONSTRUCT CRCP OVER EXISTING PAVEMENT AND PLACE HMA.
Location Description	KERN COUNTY AT AND NEAR ROSAMOND AND MOJAVE FROM 1.4 MILES SOUTH OF DAWN ROAD OVERCROSSING TO 0.5 MILE NORTH OF SILVER QUEEN ROAD OVERCROSSING
QA Service Level	1 (Verified on 11/06/2020)

Sample Taken Date	12/08/2020	Sample Unique Key	11
Will the laboratory/organization for which you are a member perform testing on this material sample?	Yes	Date that the sample was received by the laboratory/organization performing the testing	12/16/2020
Sample type	Department Acceptance	A brief description of the sample	3/4" HMA-A-SP R25 0.8% Dry Lime
The quantity of what the sample constitutes	1 Bag Coldfeed Agg., 1 Bag L.T. Agg.	From where was the sample collected	Manufacturer
First name of sampler or witnessed by	Granite Construction Company Littlerock	Last name of sampler or witnessed by	QC
Title of sampler		Telephone number of sampler
Laboratory sample identification	0704A-20	Linked DIME Sample ID
The fabricator/manufacturer/facility name	Granite Construction Company Littlerock	Transportation Laboratory (TL) Number
Inspector Lot Number from the Transportation Laboratory (TL) Form		Structure unique identifier
Structure name

Material Type	Aggregate	Source Identification (SMARA, name of Pit or Job Site)	91-19-0046, 91-19-0008
The fabricator's/manufacturer's product name for the sample	3/4 HMA-A-SP R25	The fabricator/manufacturer designation for the sample
The plant number	13554	A detailed description of where the material sample was collected	Belt Cut at Granite Little Rock Plant
Where the material sample would have been placed if not sampled	Asphalt Paving	Primary Aggregate Nominal Size	3/4 inch
The concrete mix design number		Lot number	1
Sublot number		Aggregate Mix Number	Not set

DIME Sample ID: 2020-12-08-11

DIME Test ID: 2020-12-08-11-3

Testing Lab: CT D08 - Fontana Southern Regional Laboratory

Test Method: CTM 202-November 2011: Method of Test for Sieve Analysis of Fine and Coarse Aggregates

Test Release Date: 2020-12-29

What size aggregate is being tested?: Combined Gradation

Individual or cumulative mass retained on each sieve?: Cumulative Mass Retained

For Combined Gradation only, has the fine aggregate sample been reduced?: No

For Combined Gradation only, use #40 Sieve?: No

Input Type: Calculated

Tester's full name: Satish Jain

Date of test: 12/20/2020

Cumulative percent passing the 3 in. sieve: 100 %

Cumulative percent passing the 2 1/2 in. sieve: 100 %

Cumulative percent passing the 2 in. sieve: 100 %

Cumulative percent passing the 1 1/2 in. sieve: 100 %

Cumulative percent passing the 1 in. sieve: 100 %

Cumulative percent passing the 3/4 in. sieve: 100 %

Cumulative percent passing the 1/2 in. sieve: 100 %

Cumulative percent passing the 3/8 in. sieve: 99 %

Cumulative percent passing the #4 sieve: 70 %

Cumulative percent passing the #8 sieve: 51 %

Cumulative percent passing the #16 sieve: 39 %

Cumulative percent passing the #30 sieve: 30 %

Cumulative percent passing the #50 sieve: 22 %

Cumulative percent passing the #100 sieve: 15 %

Cumulative percent passing the #200 sieve: 10 %

General comments (publicly viewable) (Max 1000 characters): Rap Gradation After Ignition ( Rap Grading used as of Lab # 0703-20)

Test was verified on 12/29/2020 ✔