Search Test Methods
Use this page to search for test methods that are currently supported in DIME. Enter part of the test method name, number or standard (ASTM, CTM, etc.) to filter the results. If you do not find a test method and you would like it to be added to DIME, please contact your METS Representative.
Displaying 141-160 of 405 results.
| Test Org | Prefix | Number | Version | Name | Part | Material Type | Sample Card |
|---|---|---|---|---|---|---|---|
| AASHTO | T | 316 | 22 | Standard Method of Test for Viscosity Determination of Asphalt Binder Using Rotational Viscometer | Asphalt Binder | View | |
| AASHTO | T | 59 | 22 | Standard Method of Test for Emulsified Asphalts | Particle Charge Cationic Emulsified (Sec. 8) | Asphaltic Emulsion | View |
| AASHTO | T | 59 | 22 | Standard Method of Test for Emulsified Asphalts | Demulsibility (Sec. 10) | Asphaltic Emulsion | View |
| AASHTO | T | 51 | 22 | Standard Method of Test for Ductility of Asphalt Materials | Asphaltic Emulsion | Asphaltic Emulsion | View |
| AASHTO | T | 59 | 22 | Standard Method of Test for Emulsified Asphalts | Cement Mixing (Sec. 12) | Asphaltic Emulsion | View |
| AASHTO | T | 59 | 22 | Standard Method of Test for Emulsified Asphalts | Storage Stability of Emulsified (Sec. 18) | Asphaltic Emulsion | View |
| ASTM | C | 39 | 21 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens | Concrete Concrete Core Precast Concrete | View | |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Proof Load with Wedge | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Proof Load | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Tensile, Yield and Elongation | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Hex Cap Screws | SMTL TM3 - Fastener Assembly | View |
| ASTM | E | 415 | 21 | Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry | SMTL TM6 - Steel Check Sample Plate | View | |
| ASTM | C | 109 | 21 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) | Cementitious | View | |
| ASTM | C | 642 | 21 | Standard Test Method for Density, Absorption, and Voids in Hardened Concrete | Concrete Concrete Core | View | |
| ASTM | C | 1611 | 21 | Standard Test Method for Slump Flow of Self-Consolidating Concrete | Concrete | View | |
| CTM | 435 | 21 | Method of Test for Two-component, Type A and AL Joint Seals | Joint Seal (Type A & AL) | View | ||
| CTM | 435 | 21 | Method of Test for Two-Component, Type A and AL Joint Seals | Cone | Asphalt Plug Joint Seal | View | |
| CTM | 435 | 21 | Method of Test for Two-Component, Type A and AL Joint Seals | Notch | Asphalt Plug Joint Seal | View | |
| ASTM | D | 217 | 21 | Standard Test Methods for Cone Penetration of Lubricating Grease | Cone Penetration | Asphalt Rubber Binder Asphalt Binder | View |
| AASHTO | T | 313 | 2025 | Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) | Asphalt Binder | View |