Search Test Methods
Use this page to search for test methods that are currently supported in DIME. Enter part of the test method name, number or standard (ASTM, CTM, etc.) to filter the results. If you do not find a test method and you would like it to be added to DIME, please contact your METS Representative.
Displaying 261-280 of 438 results.
| Test Org | Prefix | Number | Version | Name | Part | Material Type | Sample Card |
|---|---|---|---|---|---|---|---|
| ASTM | E | 415 | 17 | Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry | SMTL TM6 - Steel Check Sample Plate | View | |
| ASTM | D | 244 | 17 | Standard Test Methods and Practices for Emulsified Asphalts | Asphaltic Emulsion | View | |
| ASTM | D | 412 | 16r21 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers-Tension | SMTL TM1 - Elastomeric Bearing Pad SMTL TM2 - Type B Elastomeric Joint Seal | View | |
| ASTM | D | 471 | 16r21 | Standard Test Method for Rubber Property - Effect of Liquids | SMTL TM2 - Type B Elastomeric Joint Seal | View | |
| ASTM | C | 297 | 16r2024 | Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions (with aging according to ASTM C481) | Sign Panel | View | |
| ASTM | C | 109 | 16a | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) | Cementitious | View | |
| ASTM | D | 217 | 16 | Standard Test Methods for Cone Penetration of Lubricating Grease | Cone Penetration | Job Mix Formula Partial Asphalt Rubber Binder Asphalt Binder | View |
| ASTM | C | 173 | 16 | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method | Concrete | View | |
| SMTL | CHEM | 16 | Steel Chemistry Analysis | SMTL TM6 - Steel Check Sample Plate | View | ||
| SMTL | TESTENV | 16 | SMTL Test Environment | SMTL TM1 - Elastomeric Bearing Pad | View | ||
| CTM | TEMP | 1 | 16 | Test Method for Monitoring Precast Concrete Curing Temperature | Curing temperature | Concrete | View |
| ASTM | C | 187 | 16 | Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste | Water Normal Consistency | Cementitious | View |
| ASTM | D | 5329 | 16 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements | Asphalt Pavement | Asphalt Rubber Binder Asphalt Binder | View |
| ASTM | D | 93 | 16 | Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester | Flash Point | Paint | View |
| ASTM | D | 6628 | 16 | Standard Specification for Color of Pavement Marking Materials | Chromaticity | Paint | View |
| ASTM | D | 3168 | 16 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints | Paint | View | |
| AASHTO | T | 59 | 16 | Standard Method of Test for Emulsified Asphalts | Residue and Oil Distillate (Sec. 6) | Asphaltic Emulsion | View |
| AASHTO | T | 59 | 16 | Standard Method of Test for Emulsified Asphalts | Viscosity (Saybolt Furol) (Sec. 9) | Asphaltic Emulsion | View |
| AASHTO | T | 166 | 16 | Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens | Method A | Hot Mix Asphalt | View |
| AASHTO | T | 59 | 16 | Standard Method of Test for Emulsified Asphalts | Emulsified Asphalt Residue Evap. (Sec. 7) | Asphaltic Emulsion | View |