Search Test Methods
Use this page to search for test methods that are currently supported in DIME. Enter part of the test method name, number or standard (ASTM, CTM, etc.) to filter the results. If you do not find a test method and you would like it to be added to DIME, please contact your METS Representative.
Displaying 241-260 of 405 results.
| Test Org | Prefix | Number | Version | Name | Part | Material Type | Sample Card |
|---|---|---|---|---|---|---|---|
| ASTM | E | 313 | 20 | Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates | Paint Thermoplastic | View | |
| CTM | 534 | 20 | Method of Test for Water Retention Efficiency of Liquid Membrane-Forming Concrete Curing Compounds | Curing Compound | View | ||
| ASTM | D | 5 | 20 | Standard Test Method for Penetration of Bituminous Materials | Asphalt Binder | View | |
| AASHTO | T | 48 | 20 | Standard Method of Test for Flash Point of Asphalt Binder by Cleveland Open Cup | Asphalt Binder Asphaltic Emulsion | View | |
| ASTM | D | 5329 | 20 | Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements | Asphalt Pavement | Asphalt Rubber Binder Asphalt Binder | View |
| AASHTO | T | 313 | 2025 | Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) | Asphalt Binder | View | |
| ASTM | C | 39 | 21 | Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens | Concrete Concrete Core Precast Concrete | View | |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Proof Load with Wedge | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Proof Load | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Tensile, Yield and Elongation | SMTL TM3 - Fastener Assembly | View |
| ASTM | F | 606 | 21 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets | Hex Cap Screws | SMTL TM3 - Fastener Assembly | View |
| ASTM | E | 415 | 21 | Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry | SMTL TM6 - Steel Check Sample Plate | View | |
| ASTM | C | 109 | 21 | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) | Cementitious | View | |
| ASTM | C | 642 | 21 | Standard Test Method for Density, Absorption, and Voids in Hardened Concrete | Concrete Concrete Core | View | |
| ASTM | C | 1611 | 21 | Standard Test Method for Slump Flow of Self-Consolidating Concrete | Concrete | View | |
| CTM | 435 | 21 | Method of Test for Two-component, Type A and AL Joint Seals | Joint Seal (Type A & AL) | View | ||
| CTM | 435 | 21 | Method of Test for Two-Component, Type A and AL Joint Seals | Cone | Asphalt Plug Joint Seal | View | |
| CTM | 435 | 21 | Method of Test for Two-Component, Type A and AL Joint Seals | Notch | Asphalt Plug Joint Seal | View | |
| ASTM | D | 217 | 21 | Standard Test Methods for Cone Penetration of Lubricating Grease | Cone Penetration | Asphalt Rubber Binder Asphalt Binder | View |
| AASHTO | T | 301 | 22 | Standard Method of Test for Elastic Recovery Test of Asphalt Materials by Means of a Ductilometer | Asphalt Binder Asphaltic Emulsion | View |