Sample Record for 2017-12-14-13
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 211796 DEA: 073X8704 EFIS: 0713000241
QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-105,405-R2.5,20.5/R21.1
Work Description: SLOPE RECONSTRUCTION AND PAVEMENT REPAIR
Location Description: LOS ANGELES COUNTY IN AND NEAR HAWTHORNE FROM EL SEGUNDO BOULEVARD UNDERCROSSING TO ROUTE 105/405 SEPARATION
Contractor Name: GRIFFITH COMPANY
Contractor Address: 12200 BLOOMFIELD AVENUE, SANTA FE SPRINGS, CA 90670
Resident Engineer: Mashhur Ali Structure Rep.: Frank Lotfi
Sample Information
DIME Sample ID: 2017-12-14-13
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 12/14/2017
Date that the sample was received by the laboratory/organization performing the testing: 12/21/2017
The quantity of what the sample constitutes: 67
A brief description of the sample: F1554 Grade 55 HDG Anchor Rods
From where was the sample collected: Fabricator
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Structural and Steel Products
Material Information
Rocap Number(s): NA
Heat Number(s): Bolt 58031133
HDG NUT A164716
Plain NUT 3068895
Washer 265467
Nut Mfg. Lot Number(s): AmeriBolt, HDG W3017
Plain W3538
Washer Mfg. Lot Number(s): Wrought Washer, 299014
Bolt Specification: F1554-GR 55
Bolt Length(s): 60"
Nut Specification: A563 DH
Washer Specification: F436
Finish: HDG one end
Diameter/Size: 2-1/2"
Bolt Mfg. Lot Number: GERDAU, NA
Rocap Test Requirement(s): NA
Lubricant Requirements(s): WAX on Galvanized
Test Results
Test 1 of 11
DIME Test ID: 2017-12-14-13-1
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By | 1 | 58031133 | 0.501 | 0.197 | 63341 | 90440 | 28 | Fred |
| |
UTM
|
67KIP
|
Temperature
|
72 f
|
Test 2 of 11
DIME Test ID: 2017-12-14-13-2
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By | 2 | 58031133 | 0.502 | 0.198 | 62489 | 89680 | 28 | Fred |
| |
UTM
|
67KIP
|
Temperature
|
72 f
|
Test 3 of 11
DIME Test ID: 2017-12-14-13-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
58031133
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
Plain and ASTM F2329 - Hot Dip
|
Product Markings
|
YELLOW PAINT
|
Size
|
2.5 in
|
Bolt Length
|
60 in
|
Gage Type
|
Pass
|
Test 4 of 11
DIME Test ID: 2017-12-14-13-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
W3017
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
LSF 2H / DH
|
Size
|
2.5 in
|
Gage Type
|
Pass
|
Test 5 of 11
DIME Test ID: 2017-12-14-13-5
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1B
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
W2543
|
Finish Coating
|
Plain
|
Product Markings
|
LSF 2H / DH
|
Size
|
2.5 in
|
Gage Type
|
Pass
|
Test 6 of 11
DIME Test ID: 2017-12-14-13-6
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
58031133
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
Plain and ASTM F2329 - Hot Dip
|
Product Markings
|
YELLOW PAINT
|
Size
|
2.5 in
|
Bolt Length
|
60 in
|
Measurement Average
|
5 mils
|
Test 7 of 11
DIME Test ID: 2017-12-14-13-7
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
W3017
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
LSF 2H / DH
|
Size
|
2.5 in
|
Bolt Length
|
no data in
|
Measurement Average
|
6.52 mils
|
Test 8 of 11
DIME Test ID: 2017-12-14-13-8
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
2990104
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
WS
|
Size
|
2.5 in
|
Bolt Length
|
no data in
|
Measurement Average
|
3.81 mils
|
Test 9 of 11
DIME Test ID: 2017-12-14-13-9
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
W3017
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
LSF 2H / DH
|
Size
|
2.5 in
|
Bolt Length
|
no data in
|
Hardness Reading Scale
|
C Scale
|
Hardness Reading Average
|
25.6
|
Spacing
|
Ok
|
Test 10 of 11
DIME Test ID: 2017-12-14-13-10
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1B
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
W3543
|
Finish Coating
|
Plain
|
Product Markings
|
LSF 2H / DH
|
Size
|
2.5 in
|
Bolt Length
|
no data in
|
Hardness Reading Scale
|
C Scale
|
Hardness Reading Average
|
24.95
|
Spacing
|
Ok
|
Test 11 of 11
DIME Test ID: 2017-12-14-13-11
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/04/2018
Date Tested: 01/04/2018
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
2990104
|
Finish Coating
|
ASTM F2329 - Hot Dip
|
Product Markings
|
WS
|
Size
|
2.5 in
|
Bolt Length
|
no data in
|
Hardness Reading Scale
|
C Scale
|
Hardness Reading Average
|
39.45
|
Spacing
|
Ok
|