Summary for Test 2020-10-12-11-10
Test performed: CTM 202-November 2011Project Information
Project Identifiers | Project ID: 214848 DEA: 081H3414 EFIS: 0818000172 |
---|---|
DIST-CO-RTE-PM | 08-SBD-210,215,259-Various |
Award Date | 05/07/2020 |
Closeout Date | 10/13/2022 |
Work Description | PLACE RHMA-G, COLD PLANE AC AND REPLACE AC SURFACING. |
Location Description | SAN BERNARDINO COUNTY ON ROUTE 210, 215 AND 259 AT VARIOUS LOCATIONS |
QA Service Level | 1 (Verified on 07/20/2020) |
Sample Information
Sample Taken Date | 10/12/2020 | Sample Unique Key | 11 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 10/13/2020 |
Sample type | Verification | A brief description of the sample | PSUE 3/4" HMA-A-SP R15 No LAS |
The quantity of what the sample constitutes | 4 Bags Coldfeed Agg., 2 Bags Rap | From where was the sample collected | Manufacturer |
First name of sampler or witnessed by | Cezar | Last name of sampler or witnessed by | All American Asphalt QC |
Title of sampler | Telephone number of sampler | ||
Laboratory sample identification | 0594A-20 | Linked DIME Sample ID | |
The fabricator/manufacturer/facility name | All American Asphalt - Corona | Transportation Laboratory (TL) Number | |
Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
Structure name |
Material Information
Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-33-0005 |
---|---|---|---|
The fabricator's/manufacturer's product name for the sample | 3/4 HMA-A-SP R15 | The fabricator/manufacturer designation for the sample | |
The plant number | 105927 | A detailed description of where the material sample was collected | Belt Cut at All American Corona Plant |
Where the material sample would have been placed if not sampled | Asphalt Paving | Primary Aggregate Nominal Size | 3/4 inch |
The concrete mix design number | Lot number | ||
Sublot number | Aggregate Mix Number | Not set |
Test Details
DIME Sample ID: 2020-10-12-11
DIME Test ID: 2020-10-12-11-10
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: CTM 202-November 2011: Method of Test for Sieve Analysis of Fine and Coarse Aggregates
Test Release Date: 2020-10-19
Test Results
What size aggregate is being tested?: Combined Gradation
Individual or cumulative mass retained on each sieve?: Cumulative Mass Retained
For Combined Gradation only, has the fine aggregate sample been reduced?: No
For Combined Gradation only, use #40 Sieve?: No
Input Type: Calculated
Tester's full name: Michael Magana, Satish Jain
Date of test: 10/16/2020
Cumulative percent passing the 3 in. sieve: 100 %
Cumulative percent passing the 2 1/2 in. sieve: 100 %
Cumulative percent passing the 2 in. sieve: 100 %
Cumulative percent passing the 1 1/2 in. sieve: 100 %
Cumulative percent passing the 1 in. sieve: 100 %
Cumulative percent passing the 3/4 in. sieve: 95 %
Cumulative percent passing the 1/2 in. sieve: 74 %
Cumulative percent passing the 3/8 in. sieve: 59 %
Cumulative percent passing the #4 sieve: 37 %
Cumulative percent passing the #8 sieve: 25 %
Cumulative percent passing the #16 sieve: 17 %
Cumulative percent passing the #30 sieve: 12 %
Cumulative percent passing the #50 sieve: 7 %
Cumulative percent passing the #100 sieve: 4 %
Cumulative percent passing the #200 sieve: 3.1 %
General comments (publicly viewable) (Max 1000 characters): Combined Virgin/RAP Gradation w/Correlation Factors Applied
Test was verified on 10/19/2020 ✔