DIME - Test Summary

Summary for Test 2020-09-03-7-1

Test performed: AASHTO T27-14

Project Identifiers	Project ID: 214774 DEA: 081F1324 EFIS: 0815000212
DIST-CO-RTE-PM	08-SBD-95-64.5/80.5
Award Date	05/04/2020
Closeout Date	01/18/2022
Work Description	PLACE RHMA-G, COLD PLANE AC AND REPLACE AC SURFACING.
Location Description	SAN BERNARDINO COUNTY ON ROUTE 95 FROM 0.5 MILE NORTH OF GOFFS ROAD TO NEVADA STATE LINE.
QA Service Level	1 (Verified on 08/25/2020)

Sample Taken Date	09/03/2020	Sample Unique Key	7
Will the laboratory/organization for which you are a member perform testing on this material sample?	Yes	Date that the sample was received by the laboratory/organization performing the testing	09/04/2020
Sample type	Verification	A brief description of the sample	JMF 1/2" RWMA-G-SP 0.25% EVO
The quantity of what the sample constitutes	10 Bags Of Aggregate	From where was the sample collected	Manufacturer
First name of sampler or witnessed by	Vulcan Bullhead City Arizona	Last name of sampler or witnessed by	QC
Title of sampler		Telephone number of sampler
Laboratory sample identification	0526-20	Linked DIME Sample ID
The fabricator/manufacturer/facility name	Vulcan Bullhead City Arizona	Transportation Laboratory (TL) Number
Inspector Lot Number from the Transportation Laboratory (TL) Form		Structure unique identifier
Structure name

Material Type	Aggregate	Source Identification (SMARA, name of Pit or Job Site)	CM2056
The fabricator's/manufacturer's product name for the sample	1/2 RWMA-G-SP	The fabricator/manufacturer designation for the sample
The plant number	387111B	A detailed description of where the material sample was collected	Belt Cut at Bullhead City Arizona
Where the material sample would have been placed if not sampled	Asphalt Paving	Primary Aggregate Nominal Size	1/2 inch
The concrete mix design number		Lot number
Sublot number		Aggregate Mix Number	Not set

DIME Sample ID: 2020-09-03-7

DIME Test ID: 2020-09-03-7-1

Testing Lab: CT D08 - Fontana Southern Regional Laboratory

Test Method: AASHTO T27-14: Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates (Sieve Analysis)

Test Release Date: 2020-09-10

What type of gradation is being tested?: Combined Gradation

Individual or cumulative mass retained on each sieve?: Cumulative Mass Retained

Does this test use 1/4 sieve? (question for HMA Gradation Type): No

Has the fine aggregate sample been reduced?: No

Input Type: Calculated

Tester's full name: Satish Jain/Dominic Montemayor

Date of test: 09/08/2020

Cumulative percent passing the 2 in. sieve: 100 %

Cumulative percent passing the 1 1/2 in. sieve: 100 %

Cumulative percent passing the 1 in. sieve: 100 %

Cumulative percent passing the 3/4 in. sieve: 100 %

Cumulative percent passing the 1/2 in. sieve: 99 %

Cumulative percent passing the 3/8 in. sieve: 83 %

Cumulative percent passing the #4 sieve: 35 %

Cumulative percent passing the #8 sieve: 21 %

Cumulative percent passing the #16 sieve: 15 %

Cumulative percent passing the #30 sieve: 11 %

Cumulative percent passing the #50 sieve: 8 %

Cumulative percent passing the #100 sieve: 5 %

Cumulative percent passing the #200 sieve: 3.9 %

General comments (publicly viewable) (Max 1000 characters): Combined Virgin Aggregate Gradation

Test was verified on 9/10/2020 ✔