Summary for Test 2020-07-01-24-7
Test performed: ASTM D4791-10Project Information
| Project Identifiers | Project ID: 214924 DEA: 080M9004 EFIS: 0812000248 COOP: 081695 |
|---|---|
| DIST-CO-RTE-PM | 08-RIV-111-18.0/19.0 |
| Award Date | Not set |
| Closeout Date | Not set |
| Work Description | The purpose of the project is to provide a grade separated crossing over the existing UPRR, SR-111 and Hammond Road in the Mecca Community that will provide the following benefits: provide a secondary access point to the Community of Mecca. |
| Location Description | The project is in Riverside County from 0.47 miles east of State Route 86 to 0.45 miles west of Johnson Street. |
| QA Service Level | 2 (Verified on 04/22/2020) |
Sample Information
| Sample Taken Date | 07/01/2020 | Sample Unique Key | 24 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 07/13/2020 |
| Sample type | Verification | A brief description of the sample | JMF 3/4" RHMA-G-SP 0.50% LAS Aggregate |
| The quantity of what the sample constitutes | 3 Bags Combined Aggregate | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | Matich Cabazon | Last name of sampler or witnessed by | QC |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0429G-20 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Matich-Cabazon | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-33-0008, 91-36-0040 |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | 3/4 RHMA-G-SP | The fabricator/manufacturer designation for the sample | |
| The plant number | CHP 68E | A detailed description of where the material sample was collected | Belt Cut at Matich Cabazon Plant |
| Where the material sample would have been placed if not sampled | Asphalt Paving | Primary Aggregate Nominal Size | 3/4 inch |
| The concrete mix design number | Lot number | ||
| Sublot number | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2020-07-01-24
DIME Test ID: 2020-07-01-24-7
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Test Release Date: 2020-07-21
Test Results
Method A - Percentage of Flat Particles, Elongated Particles, and Flat & Elongated Particles
Method B - Flat & Elongated Particles
Method: B
Determination: By Mass
Dimensional ratio used: 5:1
Input Type: Calculated
Tester's full name: Satish Jain
Date of test: 07/16/2020
Weighted percentage of particles (by mass) that were flat and elongated: 1 %
Weighted percentage of particles (by mass) that were not flat and elongated: 99 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 7/21/2020 ✔