Summary for Test 2019-05-07-9-4
Test performed: AASHTO T84-14Project Information
| Project Identifiers | Project ID: 213650 DEA: 081E8504 EFIS: 0814000114 |
|---|---|
| DIST-CO-RTE-PM | 08-SBD-142-0.0/5.8 |
| Award Date | 11/19/2018 |
| Closeout Date | 08/28/2020 |
| Work Description | COLD PLANE/OVERLAY, HMA DIKES, INSTALL MGS AND DRAINAGE FACILITIES |
| Location Description | SAN BERNARDINO COUNTY IN AND NEAR CHINO HILLS FROM ORANGE COUNTY LINE TO ROUTE 142/71 SEPARATION. |
| QA Service Level | 1 (Verified on 04/16/2019) |
Sample Information
| Sample Taken Date | 05/07/2019 | Sample Unique Key | 9 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 05/10/2019 |
| Sample type | Verification | A brief description of the sample | 3/4 RWMA-G-SP |
| The quantity of what the sample constitutes | JMF 4 bags | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | All American Corona | Last name of sampler or witnessed by | QC |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0277G-19 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | All American Corona | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-33-0005::ALL AMERICAN ASPHALT |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | 3/4 RHMA-G-SP WMA | The fabricator/manufacturer designation for the sample | 108835 |
| The plant number | Unknown | A detailed description of where the material sample was collected | Belt Cut at Plant |
| Where the material sample would have been placed if not sampled | Unknown | Primary Aggregate Nominal Size | 3/4 inch |
| The concrete mix design number | Unknown | Lot number | Unknown |
| Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2019-05-07-9
DIME Test ID: 2019-05-07-9-4
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: AASHTO T84-14: Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate (Fine Specific Gravity)
Test Release Date: 2019-06-06
Test Results
Input Type: Measured
Tester's full name: Danilo Ferrer
Date of test: 05/15/2019
Mass of saturated surface dry sample (before pycnometer) (S): 500 grams
Mass of the pycnometer with water and aggregate (C): 968.7 grams
Mass of the pycnometer with water (B): 653.9 grams
Mass of the oven dried sample (before pycnometer) (A): 491.1 grams
Mass of the saturated surface dry aggregate (for absorption) (S): 500 grams
Mass of the oven dry aggregate (for absorption) (A): 491.1 grams
Test Sample Preparation: Total Saturation
Bulk specific gravity: 2.652
Bulk specific gravity (SSD Basis): 2.700
Apparent specific gravity: 2.786
Absorption: 1.8 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 5/30/2019 ✔