Summary for Test 2018-05-03-1-2
Test performed: ASTM A370-15Project Information
Project Identifiers | Project ID: 211803 DEA: 120M6104 EFIS: 1212000121 |
---|---|
DIST-CO-RTE-PM | 12-ORA-55,57,91-17.5/17.9;15.2/16.0;5.8/6.8;8.7/R9.5 |
Award Date | 12/21/2016 |
Closeout Date | 06/21/2021 |
Work Description | INSTALL ADDITIONAL LIGHTING AT SEPARATIONS AND UPGRADE GUARDRAIL |
Location Description | ORANGE COUNTY IN ANAHEIM ON ROUTES 55, 57, 91 AT ROUTE 91/57 SEPARATION AND ROUTE 91/55 SEPARATION |
QA Service Level | 1 (Verified on 01/12/2017) |
Sample Information
Sample Taken Date | 05/03/2018 | Sample Unique Key | 1 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 05/07/2018 |
Sample type | Quality Assurance | A brief description of the sample | 2 1/2 x 4-5 anchor bolt |
The quantity of what the sample constitutes | 3 | From where was the sample collected | Fabricator |
First name of sampler or witnessed by | David | Last name of sampler or witnessed by | Flygare |
Title of sampler | CA METS QA Inspector | Telephone number of sampler | 801-669-2984 |
Laboratory sample identification | Unknown | Linked DIME Sample ID | Unknown |
The fabricator/manufacturer/facility name | UIS | Transportation Laboratory (TL) Number | Unknown |
Inspector Lot Number from the Transportation Laboratory (TL) Form | B76-083-18 | Structure unique identifier | Not set |
Structure name | Not set |
Material Information
Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | n/a |
---|---|---|---|
Heat Number(s) | PL16108459 | Nut Mfg. Lot Number(s) | n/a |
Washer Mfg. Lot Number(s) | n/a | Bolt Specification | F1554 Gr.55 |
Bolt Length(s) | 4'-5" | Nut Specification | n/a |
Washer Specification | n/a | Finish | HDG/plain |
Diameter/Size | 2 1/2" x 4'-5" | Bolt Mfg. Lot Number | PL1610845901 |
Rocap Test Requirement(s) | none | Lubricant Requirements(s) | none |
Test Details
DIME Sample ID: 2018-05-03-1
DIME Test ID: 2018-05-03-1-2
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM A370-15: Standard Test Methods and Definitions for Mechanical Testing of Steel Products (Tensile - Round Sample)
Test Release Date: 2018-05-16
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Brian
Date of test: 05/09/2018
UTM: 67KIP
Temperature: 72 f
Num | Sample | Heat Number | Diameter (in) | Area (sqin) | Stress at Offset (psi) | Tensile Strength (psi) | Elongation in 4 x d (%) | Tested By |
---|---|---|---|---|---|---|---|---|
1 | 2 | PL16108459 | 0.502 | 0.198 | 59157 | 81860 | 31.3 | Brian |
General comments (publicly viewable) (Max 1000 characters):
Test Graph
Source: Partner Data Point FileTest graph for the Sample
Test was verified on 5/9/2018 ✔