Summary for Test 2020-07-02-14-7
Test performed: ASTM D4791-10Project Information
Project Identifiers | Project ID: 214849 DEA: 081J9404 EFIS: 0818000139 |
---|---|
DIST-CO-RTE-PM | 08-SBD-18,247-68.5/87.9,46.0/49.0 |
Award Date | 05/21/2020 |
Closeout Date | 11/09/2021 |
Work Description | REPLACE ASPHALT CONCRETE SURFACING AND STRIPING. |
Location Description | SAN BERNARDINO COUNTY ON ROUTE 18 FROM 1.4 MILES NORTH OF CAMP ROCK ROAD TO CENTRAL ROAD AND ON ROUTE 247 FROM 0.1 MILE SOUTH OF RABBIT SPRINGS ROAD TO 2.1 MILES SOUTH OF NORTHSIDE ROAD |
QA Service Level | 1 (Verified on 10/21/2020) |
Sample Information
Sample Taken Date | 07/02/2020 | Sample Unique Key | 14 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 07/09/2020 |
Sample type | Verification | A brief description of the sample | JMF 3/4" HMA-A-SP R15 0.75%LAS |
The quantity of what the sample constitutes | 8 Bags Agg., 2 Bags Rap | From where was the sample collected | Manufacturer |
First name of sampler or witnessed by | Vulcan Oro Grande | Last name of sampler or witnessed by | QC |
Title of sampler | Telephone number of sampler | ||
Laboratory sample identification | 0413A-20 | Linked DIME Sample ID | |
The fabricator/manufacturer/facility name | Vulcan- Oro Grande | Transportation Laboratory (TL) Number | |
Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
Structure name |
Material Information
Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-36-0022 |
---|---|---|---|
The fabricator's/manufacturer's product name for the sample | 3/4 HMA-A-SP R15 | The fabricator/manufacturer designation for the sample | Unknown |
The plant number | 220991 ORO SJR | A detailed description of where the material sample was collected | Belt Cut at Vulcan Oro Grande Plant |
Where the material sample would have been placed if not sampled | Asphalt Paving | Primary Aggregate Nominal Size | 3/4 inch |
The concrete mix design number | Unknown | Lot number | Unknown |
Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
DIME Sample ID: 2020-07-02-14
DIME Test ID: 2020-07-02-14-7
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Test Release Date: 2020-07-22
Test Results
Method A - Percentage of Flat Particles, Elongated Particles, and Flat & Elongated Particles
Method B - Flat & Elongated Particles
Method: B
Determination: By Mass
Dimensional ratio used: 5:1
Input Type: Calculated
Tester's full name: Satish Jain
Date of test: 07/17/2020
Weighted percentage of particles (by mass) that were flat and elongated: 1 %
Weighted percentage of particles (by mass) that were not flat and elongated: 99 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 7/22/2020 ✔