Summary for Test 2020-02-11-2-1
Test performed: ASTM F606-14Project Information
| Project Identifiers | Project ID: 213489 Permit Numbers: 0817NMC1320 0819NRT0801 0819NRW0944 0819NRT0802 0819NRW0952 0819NRW1158 0819NRW1299 0820NRT0046 0820NRT0047 |
|---|---|
| DIST-CO-RTE-PM | 08---27.05/27.55 |
| Award Date | 06/01/2018 |
| Closeout Date | 06/23/2021 |
| Work Description | Enter onto Interstate 10 (I-10) right of way at Mountain View Avenue in the City of Redlands, to perform I-10 EB and WB off-ramps widening, install curb and gutter, ADA curb ramps, modify existing traffic signal, extend drainage box culvert, and install erosion control as per plans and specificatio |
| Location Description | I-10, EB and WB off-ramps, Loma Linda |
| QA Service Level | 1 (Verified on 08/13/2019) |
Sample Information
| Sample Taken Date | 02/11/2020 | Sample Unique Key | 2 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 02/14/2020 |
| Sample type | Quality Assurance | A brief description of the sample | 3/4"-10 x 15" x 3" |
| The quantity of what the sample constitutes | 7 | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | Brian | Last name of sampler or witnessed by | Murray |
| Title of sampler | Telephone number of sampler | 213 435 4055 | |
| Laboratory sample identification | Linked DIME Sample ID | ||
| The fabricator/manufacturer/facility name | Blue Circle Corp | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | L140-044-20 | Structure unique identifier | |
| Structure name |
Material Information
| Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | |
|---|---|---|---|
| Heat Number(s) | 3093312 | Nut Mfg. Lot Number(s) | |
| Washer Mfg. Lot Number(s) | Bolt Specification | F1554 Grade 55 | |
| Bolt Length(s) | 15" x 3" | Nut Specification | n/a |
| Washer Specification | n/a | Finish | Hot Dipped Galvanized |
| Diameter/Size | 3/4" | Bolt Mfg. Lot Number | |
| Rocap Test Requirement(s) | Lubricant Requirements(s) |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2020-02-11-2
DIME Test ID: 2020-02-11-2-1
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2020-02-18
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: spaine
Date of test: 02/14/2020
UTM: 400kip
Temperature: 72
| Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 1A | UNC 3/4 | 0.334 | 32377 | 144 | 96846 | 70720 | 23620 | F1554 Full Length Tensile |
General comments (publicly viewable) (Max 1000 characters): F1554 Full Length Tensile
Test Graph
Source: Bluehill Data Point FileTest was verified on 2/18/2020 ✔