Summary for Test 2019-11-12-13-7
Test performed: ASTM D4791-10Project Information
| Project Identifiers | Project ID: 214397 DEA: 120N3204 EFIS: 1213000196 |
|---|---|
| DIST-CO-RTE-PM | 12-ORA-91-R9.8/R18.9 |
| Award Date | 11/07/2019 |
| Closeout Date | 07/01/2022 |
| Work Description | CONST PRECAST SLAB REPLACEMENT, COLD PLANE AC PVMT AND PLACE RHMA. |
| Location Description | ORANGE COUNTY IN ANAHEIM AND YORBA LINDA FROM 0.3 MILE WEST OF LAKEVIEW AVENUE OVERCROSSING TO RIVERSIDE COUNTY LINE |
| QA Service Level | 1 (Verified on 12/02/2019) |
Sample Information
| Sample Taken Date | 11/12/2019 | Sample Unique Key | 13 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 11/14/2019 |
| Sample type | Verification | A brief description of the sample | 1/2 RHMA-G-SP |
| The quantity of what the sample constitutes | JMF 3 Bags | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | RJ Noble Orange | Last name of sampler or witnessed by | QC |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0683G-19 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Hanson Aggregates, Mayhew Aggregates | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | Hanson Aggregates, Mayhew Aggregates |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | 1/2 RHMA-G-SP | The fabricator/manufacturer designation for the sample | 50R003ARSPO |
| The plant number | Unknown | A detailed description of where the material sample was collected | Belt Cut at RJ Noble Orange Plant |
| Where the material sample would have been placed if not sampled | Unknown | Primary Aggregate Nominal Size | 1/2 inch |
| The concrete mix design number | Unknown | Lot number | Unknown |
| Sublot number | Unknown | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2019-11-12-13
DIME Test ID: 2019-11-12-13-7
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Test Release Date: 2020-05-07
Test Results
Method A - Percentage of Flat Particles, Elongated Particles, and Flat & Elongated Particles
Method B - Flat & Elongated Particles
Method: B
Determination: By Mass
Dimensional ratio used: 1:5
Input Type: Calculated
Tester's full name: Danilo Ferrer
Date of test: 11/21/2019
Weighted percentage of particles (by mass) that were flat and elongated: 8 %
Weighted percentage of particles (by mass) that were not flat and elongated: 92 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 5/7/2020 ✔