Summary for Test 2017-06-09-1-1
Test performed: ASTM F606-14Project Information
Project Identifiers | Project ID: 210097 DEA: 100L9704 EFIS: 1012000053 |
---|---|
DIST-CO-RTE-PM | 10-TUO-120-R19.5/R20.0 |
Award Date | 02/22/2016 |
Closeout Date | 10/09/2018 |
Work Description | REPLACE DECK AND RETROFIT BRIDGE. |
Location Description | IN TUOLUMNE COUNTY ON STATE ROUTE 120 FROM 7.6 MILES EAST OF YOSEMITEJUNCTION TO 4.8 MILES WEST OF THE TOWN OF MOCCASIN AT TUOLUMNE RIVER/DON PEDRO RESERVOIR (JAMES E. |
QA Service Level | 1 (Verified on 12/19/2014) |
Sample Information
Sample Taken Date | 06/09/2017 | Sample Unique Key | 1 |
---|---|---|---|
Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 06/14/2017 |
Sample type | Acceptance | A brief description of the sample | A449 HDG Tie Rod |
The quantity of what the sample constitutes | 28 | From where was the sample collected | Manufacturer |
First name of sampler or witnessed by | Scott | Last name of sampler or witnessed by | Leavitt |
Title of sampler | QA Inspector | Telephone number of sampler | 5105900119 |
Laboratory sample identification | Unknown | Linked DIME Sample ID | Unknown |
The fabricator/manufacturer/facility name | Portland Bolt | Transportation Laboratory (TL) Number | Unknown |
Inspector Lot Number from the Transportation Laboratory (TL) Form | S28-170-17 | Structure unique identifier | Not set |
Structure name | Not set |
Material Information
Material Type | SMTL TM3 - Fastener Assembly | Rocap Number(s) | N/A |
---|---|---|---|
Heat Number(s) | 75062939 | Nut Mfg. Lot Number(s) | |
Washer Mfg. Lot Number(s) | Bolt Specification | A449 | |
Bolt Length(s) | 74-1/8, 72-5/8, 70-1/4, 66-5/8, 64-5/8, 63-1/ | Nut Specification | N/A |
Washer Specification | N/A | Finish | HDG |
Diameter/Size | 1.125 | Bolt Mfg. Lot Number | 12478 |
Rocap Test Requirement(s) | No | Lubricant Requirements(s) |
Test Details
DIME Sample ID: 2017-06-09-1
DIME Test ID: 2017-06-09-1-1
Testing Lab: CT HQ - Sacramento Structural Materials Testing Laboratory
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Test Release Date: 2017-06-22
Test Results
Number of Samples: 1
Input Type: Measured
Tester's full name: Arnold
Date of test: 06/14/2017
UTM: 400KIP
Temperature: 71
Num | Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments |
---|---|---|---|---|---|---|---|---|---|
1 | 1A | A449 w/ Clevis | 0.763 | 86364 | 384 | 113190 | 98338 | 75032 | A449 w/ Clevis |
General comments (publicly viewable) (Max 1000 characters): A449 w/ Clevis
Test Graph
Source: Partner Data Point FileTest was verified on 6/15/2017 ✔