Summary for Test 2021-06-23-23-8
Test performed: ASTM D4791-10Project Information
| Project Identifiers | Project ID: 215535 DEA: 081L6704 |
|---|---|
| DIST-CO-RTE-PM | 08-SBD-62-15.1/29.3 |
| Award Date | 04/27/2021 |
| Closeout Date | 05/26/2022 |
| Work Description | REPLACE ASPHALT CONCRETE SURFACING, SLURRY SEAL, AND STRIPING. |
| Location Description | SAN BERNARDINO COUNTY AT AND NEAR JOSHUA TREE FROM YUCCA MESA ROAD TO BERMUDA AVENUE |
| QA Service Level | 1 (Verified on 07/06/2021) |
Sample Information
| Sample Taken Date | 06/23/2021 | Sample Unique Key | 23 |
|---|---|---|---|
| Will the laboratory/organization for which you are a member perform testing on this material sample? | Yes | Date that the sample was received by the laboratory/organization performing the testing | 07/07/2021 |
| Sample type | Verification | A brief description of the sample | JMF 3/4" HMA-A-SP R22 0.75% LAS |
| The quantity of what the sample constitutes | 6 Bags of Combined Aggregate, 4 Bags of Rap | From where was the sample collected | Manufacturer |
| First name of sampler or witnessed by | Matich Cabazon | Last name of sampler or witnessed by | QC |
| Title of sampler | Telephone number of sampler | ||
| Laboratory sample identification | 0405A-21 | Linked DIME Sample ID | |
| The fabricator/manufacturer/facility name | Matich Cabazon | Transportation Laboratory (TL) Number | |
| Inspector Lot Number from the Transportation Laboratory (TL) Form | Structure unique identifier | ||
| Structure name |
Material Information
| Material Type | Aggregate | Source Identification (SMARA, name of Pit or Job Site) | 91-33-0008::CABAZON QUARRY |
|---|---|---|---|
| The fabricator's/manufacturer's product name for the sample | 3/4 HMA-A-SP R22 | The fabricator/manufacturer designation for the sample | |
| The plant number | CHP 64D | A detailed description of where the material sample was collected | Belt Cut at Matich Cabazon Plant |
| Where the material sample would have been placed if not sampled | Asphalt Paving | Primary Aggregate Nominal Size | 3/4 inch |
| The concrete mix design number | Lot number | ||
| Sublot number | Aggregate Mix Number | Not set |
Test Details
Test Details QR Code
Scan this code to open this Test Details view on another device.
Sample Details QR Code
Scan this code to open this Sample Details view on another device.
DIME Sample ID: 2021-06-23-23
DIME Test ID: 2021-06-23-23-8
Testing Lab: CT D08 - Fontana Southern Regional Laboratory
Test Method: ASTM D4791-10: Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019) (Flat and Elongated Particles)
Test Release Date: 2021-07-19
Test Results
Method A - Percentage of Flat Particles, Elongated Particles, and Flat & Elongated Particles
Method B - Flat & Elongated Particles
Method: B
Determination: By Mass
Dimensional ratio used: 5:1
Input Type: Calculated
Tester's full name: Satish Jain
Date of test: 07/14/2021
Weighted percentage of particles (by mass) that were flat and elongated: 0 %
Weighted percentage of particles (by mass) that were not flat and elongated: 100 %
General comments (publicly viewable) (Max 1000 characters):
Test was verified on 7/19/2021 ✔