Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 214628 DEA: 031G6604 EFIS: 0319000116
QA Service Level: 1
DIST-CO-RTE-PM: 03-BUT-162-12.6/15.6
Work Description: COLD IN-PLACE RECYCLING, RHMA-G OVERLAY, AND COLD PLANE AC PAVEMENT.
Location Description: BUTTE COUNTY IN AND NEAR OROVILLE FROM 0.8 MILE EAST OF WILBUR ROAD TO FEATHER RIVER BRIDGE
Contractor Name: LAMON CONSTRUCTION
Contractor Address: 871 Von Geldern Way, Yuba City, California 95991
Resident Engineer: Ryan Johnson Structure Rep.: Unknown
DIME Sample ID: 2020-04-17-18
TL Number from the TL Form: C779100
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/17/2020
Date that the sample was received by the laboratory/organization performing the testing: 04/20/2020
The quantity of what the sample constitutes: JMF Verification
A brief description of the sample: 1/2 inch RHMA-G
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Teichert-Hallwood Drum Plant
DIME Test ID: 2020-04-17-18-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 11/13/2020
Date Tested: 06/01/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
What temperature unit is used?
|
Fahrenheit
|
Test procedure used?
|
Method A
|
Mass of HMA Sample prior to ignition
|
no data
|
Corrected Asphalt Binder Content
|
7.80 %
|
Mass Loss
|
no data
|
Correction Factor (Percent by mass of HMA Specimen)
|
no data
|
Moisture Content
|
no data
|
Temperature Compensation Factor
|
no data
|
Test Temperature
|
no data
|
DIME Test ID: 2020-04-17-18-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 11/13/2020
Date Tested: 06/01/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-017
Bulk Specific Gravity
|
2.340
|
Bulk Specific Gravity 2
|
2.338
|
Bulk Specific Gravity 3
|
2.345
|
Average Bulk Specific Gravity
|
2.341
|
DIME Test ID: 2020-04-17-18-4
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 11/13/2020
Date Tested: 06/01/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-017
Number of tests
|
1
|
What is the unit of measurement for theoretical density?
|
US Units
|
Mass Determination
|
Air
|
Specific Gravity for Sample 1
|
2.465
|
Theoretical maximum density at 25°C (77°F)
|
no data
|
DIME Test ID: 2020-04-17-18-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 11/13/2020
Date Tested: 06/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids
|
5.1 %
|
Percent Air Voids 2
|
5.2
|
Percent Air Voids 3
|
4.9
|
Percent Air Voids Average
|
5.0
|
DIME Test ID: 2020-04-17-18-6
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 11/13/2020
Date Tested: 06/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
Unit system used?
|
SI Units
|
Average Dry Tensile Strength
|
144 psi
|
Average Wet Tensile Strength
|
121 psi
|
Tensile Strength Ratio
|
84
|
DIME Test ID: 2020-04-17-18-7
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 11/13/2020
Date Tested: 06/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: complies
Additional Comments When Verified: JMF20-017
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A)
|
25000
|
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B)
|
25000
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A)
|
5.22 mm
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B)
|
3.43 mm
|
Stripping Inflection Point (Wheel A)
|
19200
|
Stripping Inflection Point (Wheel B)
|
25000
|
DIME Test ID: 2020-04-17-18-8
Test Method: AASHTO T312-14: Preparing and Determining the Density of Asphalt Mixture Specimens by Means of the Superpave Gyratory Compactor (Method of Compaction)
Verified Date: 11/13/2020
Date Tested: 06/02/2020
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF20-017
Test Result Compliance: not applicable
Additional Comments When Verified: JMF20-017
Volume of the specimen
|
1732.940 cm^3
|
Uncorrected relative density (Gmmu50-150)
|
no data
|
Relative density (Gmm50-150)
|
2.3 %
|
Air Voids (AV50-150)
|
5.0 %
|