Print Report | Back to Sample Detail

Sample Record for 2020-04-15-3

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 214587 DEA: 101J1604 EFIS: 1018000180 QA Service Level: 1
DIST-CO-RTE-PM: 10-STA-132-27.9/41.0
Work Description: COLD PLANE AC PAVEMENT, RHMA OVERLAY AND SLURRY SEAL.
Location Description: STANISLAUS COUNTY IN AND NEAR WATERFORD FROM G STREET TO 1.2 MILES EAST OF RUSHING ROAD
Contractor Name: George Reed
Contractor Address: PO Box, Greenwood, CA 95635
Resident Engineer: Ranbir Bhullar Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2020-04-15-3
TL Number from the TL Form: C033878
Sample Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 04/15/2020
Date that the sample was received by the laboratory/organization performing the testing: 04/15/2020
The quantity of what the sample constitutes: 16 boxes of 3/4" Type A HMA with RAP
A brief description of the sample: Type A HMA with RAP
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed Inc

Material Information

HMA Type: Type A HMA
HMA Grading: 3/4 inch
Lot number: Unknown
Sublot number: Unknown
HMA Mix Number:

Test Results

Test 1 of 7

DIME Test ID: 2020-04-15-3-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 04/28/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
What temperature unit is used? Fahrenheit
Test procedure used? Method A
Mass of HMA Sample prior to ignition 2017.9 g
Corrected Asphalt Binder Content 4.91 %
Mass Loss no data
Correction Factor (Percent by mass of HMA Specimen) 0.67 %
Moisture Content 0.17 %
Temperature Compensation Factor no data
Test Temperature 538 F

Test 2 of 7

DIME Test ID: 2020-04-15-3-2
Test Method: AASHTO T329-13: Standard Method of Test for Moisture Content of Asphalt Mixtures by Oven Method (Moisture Content)
Verified Date: 04/28/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Moisture Content 0.50 %
Percent Change 0.5 %

Test 3 of 7

DIME Test ID: 2020-04-15-3-3
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 04/28/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Bulk Specific Gravity 2.381
Bulk Specific Gravity 2 2.385
Bulk Specific Gravity 3 2.384
Average Bulk Specific Gravity 2.383

Test 4 of 7

DIME Test ID: 2020-04-15-3-4
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 04/28/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: not applicable
Additional Comments When Verified:
Number of tests 1
What is the unit of measurement for theoretical density? US Units
Mass Determination Water
Specific Gravity for Sample 1 2.460
Theoretical maximum density at 25°C (77°F) no data

Test 5 of 7

DIME Test ID: 2020-04-15-3-5
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 04/28/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Percent Air Voids 3.2 %
Percent Air Voids 2 3.0
Percent Air Voids 3 3.1
Percent Air Voids Average 3.1

Test 6 of 7

DIME Test ID: 2020-04-15-3-6
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 05/01/2020
Date Tested: 04/30/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Unit system used? SI Units
Average Dry Tensile Strength 284 psi
Average Wet Tensile Strength 192 psi
Tensile Strength Ratio 67.6

Test 7 of 7

DIME Test ID: 2020-04-15-3-7
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 05/01/2020
Date Tested: 04/17/2020
Submitted By Organization: CT HQ - Sacramento Hot Mix Asphalt Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A) 15000
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B) 15000
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A) 3.65 mm
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B) 2.2 mm
Stripping Inflection Point (Wheel A) >10000
Stripping Inflection Point (Wheel B) >10000