Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 213741 DEA: 07325704 EFIS: 0716000089
QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-5-1.7
Work Description: BUILDING CONSTRUCTION IN LOS ANGELES COUNTY IN SANTA FE SPRINGS AT 14044 FREEWAY DRIVE.
Location Description: Santa Fe Springs, At 14044 Freeway Drive.
Contractor Name: AWI Builders Inc
Contractor Address: 7831 Paramount Bl, Pico Rivera Ca 90660
Resident Engineer: Mashhur Ali Structure Rep.: Nelson Parada
DIME Sample ID: 2019-12-11-29
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 12/11/2019
Date that the sample was received by the laboratory/organization performing the testing:
The quantity of what the sample constitutes: 80 EA
A brief description of the sample: F1554 Anchor Bolt
From where was the sample collected: Distributor
Laboratory sample identification:
Structure unique identifier:
Structure name: Building Work
The fabricator/manufacturer/facility name: Cordova Bolt
Rocap Number(s): N/A
Heat Number(s): 3063603
Nut Mfg. Lot Number(s): 413065A
Washer Mfg. Lot Number(s): N/A
Bolt Specification: F1554 Gr. 55
Bolt Length(s): 18"
Nut Specification: A563 Gr. DH
Washer Specification: N/A
Finish: Plain
Diameter/Size: 5/8" with 6" thread on each end
Bolt Mfg. Lot Number: N/A
Rocap Test Requirement(s): NA
Lubricant Requirements(s):
DIME Test ID: 2019-12-11-29-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 12/17/2019
Date Tested: 12/16/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: F1554 Gr 55 Rod
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Size | Area (in^2) | Peak Load (lbf) | Peak Load (kN) | Tensile Strength (psi) | Stress at Offset (psi) | Load at Offset (lbf) | Comments | 1 | UNC 5/8 | 0.226 | 21085 | 93 | 93273 | 68416 | 15462 | F1554 Gr 55 Rod |
| |
UTM
|
400kip
|
Temperature
|
72
|
DIME Test ID: 2019-12-11-29-2
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 12/17/2019
Date Tested: 12/16/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples
|
1
|
Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | 1 | 413065A | | 39920 | | Nut Proof | bewing |
| |
UTM
|
450kip
|
Temperature
|
72 f
|
DIME Test ID: 2019-12-11-29-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 12/17/2019
Date Tested: 12/16/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
3063603
|
Mfg. Lot Number
|
no data
|
Finish Coating
|
Plain
|
Product Markings
|
YELLOW PAINT
|
Size
|
.625 in
|
Bolt Length
|
17 in
|
Gage Type
|
Pass
|
DIME Test ID: 2019-12-11-29-4
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 12/17/2019
Date Tested: 12/16/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No.
|
1A
|
Rocap Number
|
no data
|
Heat Number(s)
|
no data
|
Mfg. Lot Number
|
413065A
|
Finish Coating
|
Plain
|
Product Markings
|
DH N
|
Size
|
.625 in
|
Gage Type
|
Pass
|