Sample Record for 2019-12-04-9
Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project Information
Project ID: 214329 DEA: 120S2404 EFIS: 1220000002
QA Service Level: 1
DIST-CO-RTE-PM: 12-ORA-91,90-6.42/6.5, 6.42
Work Description: repair a damage steel girder by heat straightening as a result of a high load vehicle hit
Location Description: Westbound Route 91 at La Palma Avenue Bridge Structure at PM 6.42
Contractor Name: Beader Construction
Contractor Address: 26320 LESTER CIRCLE, CORONA CA 92883
Resident Engineer: Kifah Ramadan Structure Rep.: Bassem Kabbara
Sample Information
DIME Sample ID: 2019-12-04-9
TL Number from the TL Form:
Sample Submitted By Organization: CT HQ - QASI Los Angeles Field Office
Sample Organization Contact: (858) 285-5797
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 12/04/2019
Date that the sample was received by the laboratory/organization performing the testing: 12/09/2019
The quantity of what the sample constitutes: 64
A brief description of the sample: 3/4"-10 x 4-1/4" F3125
From where was the sample collected: Other
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Unytite Inc
Material Information
Rocap Number(s): 25618-20493880
Heat Number(s): 20493880
Nut Mfg. Lot Number(s): 25825-177300
Washer Mfg. Lot Number(s): D3124
Bolt Specification: ASTM F3125
Bolt Length(s): 4-1/4
Nut Specification: ASTM A563 Gr. DH
Washer Specification: ASTM 436
Finish: MG
Diameter/Size: 3/4"-10
Bolt Mfg. Lot Number: 25618-20493880
Rocap Test Requirement(s): Yes
Lubricant Requirements(s): Yes
Test Results
Test 1 of 16
DIME Test ID: 2019-12-04-9-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325 Wedge Tensile
Test Result Compliance:
Additional Comments When Verified:
|
Number of Bolt Samples
|
1
|
| Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Wedge Angle (deg) | Comments | Tested By | | 1A | 25618-20493880 | 0.7500 | 53386 | 237.47 | 10.00 | A325 Wedge Tensile | spaine |
| |
|
UTM
|
450kip
|
|
Temperature
|
no data
|
Test 2 of 16
DIME Test ID: 2019-12-04-9-2
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
|
Number of Samples
|
1
|
| Sample | Bolt Mfg. Lot Number | Size (in) | Peak Load (lbf) | Peak Load (kN) | Comments | Tested By | | 1A | 25825-177300 | | 50980 | | Nut Proof Load | spaine |
| |
|
UTM
|
450kip
|
|
Temperature
|
72 f
|
Test 3 of 16
DIME Test ID: 2019-12-04-9-3
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Gage Type
|
Pass
|
Test 4 of 16
DIME Test ID: 2019-12-04-9-4
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Gage Type
|
Pass
|
Test 5 of 16
DIME Test ID: 2019-12-04-9-5
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Gage Type
|
Pass
|
Test 6 of 16
DIME Test ID: 2019-12-04-9-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Measurement Average
|
3.61 mils
|
Test 7 of 16
DIME Test ID: 2019-12-04-9-10
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Measurement Average
|
2.71 mils
|
Test 8 of 16
DIME Test ID: 2019-12-04-9-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25618-20493880
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
A325TC USA
|
|
Size
|
.75 in
|
|
Bolt Length
|
4.25 in
|
|
Measurement Average
|
2.93 mils
|
Test 9 of 16
DIME Test ID: 2019-12-04-9-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25825-177300
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
DH U
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.79 mils
|
Test 10 of 16
DIME Test ID: 2019-12-04-9-13
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25825-177300
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
DH U
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.68 mils
|
Test 11 of 16
DIME Test ID: 2019-12-04-9-14
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
25825-177300
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
DH U
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
3 mils
|
Test 12 of 16
DIME Test ID: 2019-12-04-9-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
D3124
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
F436 P
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.08 mils
|
Test 13 of 16
DIME Test ID: 2019-12-04-9-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
D3124
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
F436 P
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.99 mils
|
Test 14 of 16
DIME Test ID: 2019-12-04-9-17
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1C
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
D3124
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
F436 P
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Measurement Average
|
2.63 mils
|
Test 15 of 16
DIME Test ID: 2019-12-04-9-18
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1A
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
D3124
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
F436 P
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
41.8
|
|
Spacing
|
Ok
|
Test 16 of 16
DIME Test ID: 2019-12-04-9-19
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 12/11/2019
Date Tested: 12/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
|
Sample No.
|
1B
|
|
Rocap Number
|
no data
|
|
Heat Number(s)
|
no data
|
|
Mfg. Lot Number
|
D3124
|
|
Finish Coating
|
ASTM B695 - Mech Galv
|
|
Product Markings
|
F436 P
|
|
Size
|
.75 in
|
|
Bolt Length
|
no data in
|
|
Hardness Reading Scale
|
C Scale
|
|
Hardness Reading Average
|
40.15
|
|
Spacing
|
Ok
|
