Print Report | Back to Sample Detail

Sample Record for 2019-01-08-1

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212185 DEA: 024G5204 EFIS: 0214000022 QA Service Level: 1
DIST-CO-RTE-PM: 02-SHA-5-R28.0 - R29.2
Work Description: PIT RIVER BRIDGE DECK & CATWALK REHABILITATION
Location Description: SHASTA COUNTY ABOUT 6 MILES NORTH OF SHASTA LAKE FROM 0.2 MILE SOUTH TO 0.9 MILE NORTH OF PIT RIVER BRIDGE OVERHEAD
Contractor Name: GOLDEN STATE BRIDGE, INC.
Contractor Address: 3701 Mallard Drive, Benicia, CA 94510
Resident Engineer: Tofael Anwar Structure Rep.: Andrew Osullivan

Sample Information

DIME Sample ID: 2019-01-08-1
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 01/08/2019
Date that the sample was received by the laboratory/organization performing the testing: 01/09/2019
The quantity of what the sample constitutes: 20
A brief description of the sample: A325 Fastener Assembly
From where was the sample collected: Job Site
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Nucor

Material Information

Rocap Number(s):
Heat Number(s): 100791937, NF09100475, NF13104445, NF15101674, 100889865, 176414
Nut Mfg. Lot Number(s): 407093A
Washer Mfg. Lot Number(s): 310706
Bolt Specification: A325 MG
Bolt Length(s): 2.25", 2.5"
Nut Specification: DH MG
Washer Specification: F436 MG
Finish: MG
Diameter/Size: 5/8
Bolt Mfg. Lot Number: 411418A, 260531A, 338564A, 365183A
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 71

DIME Test ID: 2019-01-08-1-1
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1A411418A5/8\"31314139.310A325Brian
UTM 400KIP
Temperature no data

Test 2 of 71

DIME Test ID: 2019-01-08-1-2
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
1B411418A5/8\"31745141.210A325Brian
UTM 400KIP
Temperature no data

Test 3 of 71

DIME Test ID: 2019-01-08-1-3
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
2A260531A5/8\"3192914210A325Brian
UTM 400KIP
Temperature no data

Test 4 of 71

DIME Test ID: 2019-01-08-1-4
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
2B260531A5/8\"32481144.510A325Brian
UTM 400KIP
Temperature no data

Test 5 of 71

DIME Test ID: 2019-01-08-1-5
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
3A338564A5/8\"31535140.310A325Brian
UTM 400KIP
Temperature no data

Test 6 of 71

DIME Test ID: 2019-01-08-1-7
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
3B338564A5/8\"32524144.710A325Brian
UTM 400KIP
Temperature no data

Test 7 of 71

DIME Test ID: 2019-01-08-1-8
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
4A365183A5/8\"33423148.710A325Brian
UTM 400KIP
Temperature no data

Test 8 of 71

DIME Test ID: 2019-01-08-1-9
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load with Wedge)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A325
Test Result Compliance:
Additional Comments When Verified:
Number of Bolt Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)Wedge Angle (deg)CommentsTested By
4B365183A5/8\"33415148.610A325Brian
UTM 400KIP
Temperature no data

Test 9 of 71

DIME Test ID: 2019-01-08-1-10
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1A407093A5/8\"34513153.52Nut Proof LoadSteve
UTM 400KIP
Temperature 72 F

Test 10 of 71

DIME Test ID: 2019-01-08-1-11
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 01/10/2019
Date Tested: 01/09/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1B407093A5/8\"34632154.05Nut Proof LoadSteve
UTM 400KIP
Temperature 72 F

Test 11 of 71

DIME Test ID: 2019-01-08-1-12
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Gage Type Pass

Test 12 of 71

DIME Test ID: 2019-01-08-1-13
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Gage Type Pass

Test 13 of 71

DIME Test ID: 2019-01-08-1-14
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Gage Type Pass

Test 14 of 71

DIME Test ID: 2019-01-08-1-15
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Gage Type Pass

Test 15 of 71

DIME Test ID: 2019-01-08-1-16
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Gage Type Pass

Test 16 of 71

DIME Test ID: 2019-01-08-1-17
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 17 of 71

DIME Test ID: 2019-01-08-1-18
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 18 of 71

DIME Test ID: 2019-01-08-1-19
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 19 of 71

DIME Test ID: 2019-01-08-1-20
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 20 of 71

DIME Test ID: 2019-01-08-1-21
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 21 of 71

DIME Test ID: 2019-01-08-1-22
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 22 of 71

DIME Test ID: 2019-01-08-1-23
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 23 of 71

DIME Test ID: 2019-01-08-1-24
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 24 of 71

DIME Test ID: 2019-01-08-1-25
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 25 of 71

DIME Test ID: 2019-01-08-1-26
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 26 of 71

DIME Test ID: 2019-01-08-1-27
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 27 of 71

DIME Test ID: 2019-01-08-1-28
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 28 of 71

DIME Test ID: 2019-01-08-1-29
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 29 of 71

DIME Test ID: 2019-01-08-1-30
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 30 of 71

DIME Test ID: 2019-01-08-1-31
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Gage Type Pass

Test 31 of 71

DIME Test ID: 2019-01-08-1-32
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Gage Type Pass

Test 32 of 71

DIME Test ID: 2019-01-08-1-33
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Gage Type Pass

Test 33 of 71

DIME Test ID: 2019-01-08-1-34
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Gage Type Pass

Test 34 of 71

DIME Test ID: 2019-01-08-1-35
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Gage Type Pass

Test 35 of 71

DIME Test ID: 2019-01-08-1-36
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Gage Type Pass

Test 36 of 71

DIME Test ID: 2019-01-08-1-37
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Measurement Average 3.53 mils

Test 37 of 71

DIME Test ID: 2019-01-08-1-38
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Measurement Average 4.5 mils

Test 38 of 71

DIME Test ID: 2019-01-08-1-39
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Measurement Average 3.87 mils

Test 39 of 71

DIME Test ID: 2019-01-08-1-40
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Measurement Average 3.81 mils

Test 40 of 71

DIME Test ID: 2019-01-08-1-41
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 411418A
Finish Coating ASTM B695 - Mech Galv
Product Markings USA A325 N
Size .625 in
Bolt Length 2.25 in
Measurement Average 4.67 mils

Test 41 of 71

DIME Test ID: 2019-01-08-1-42
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3 mils

Test 42 of 71

DIME Test ID: 2019-01-08-1-43
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.42 mils

Test 43 of 71

DIME Test ID: 2019-01-08-1-44
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.2 mils

Test 44 of 71

DIME Test ID: 2019-01-08-1-45
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.43 mils

Test 45 of 71

DIME Test ID: 2019-01-08-1-46
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 260531A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.71 mils

Test 46 of 71

DIME Test ID: 2019-01-08-1-47
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 5.83 mils

Test 47 of 71

DIME Test ID: 2019-01-08-1-48
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 2.32 mils

Test 48 of 71

DIME Test ID: 2019-01-08-1-49
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.43 mils

Test 49 of 71

DIME Test ID: 2019-01-08-1-50
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.5 mils

Test 50 of 71

DIME Test ID: 2019-01-08-1-51
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 3E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 338564A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 2.2 mils

Test 51 of 71

DIME Test ID: 2019-01-08-1-52
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.73 mils

Test 52 of 71

DIME Test ID: 2019-01-08-1-53
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 2.83 mils

Test 53 of 71

DIME Test ID: 2019-01-08-1-54
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 2.79 mils

Test 54 of 71

DIME Test ID: 2019-01-08-1-55
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.01 mils

Test 55 of 71

DIME Test ID: 2019-01-08-1-56
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 4E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 365183A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 N
Size .625 in
Bolt Length 2.5 in
Measurement Average 3.4 mils

Test 56 of 71

DIME Test ID: 2019-01-08-1-57
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Bolt Length no data in
Measurement Average 3.83 mils

Test 57 of 71

DIME Test ID: 2019-01-08-1-58
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Bolt Length no data in
Measurement Average 3.91 mils

Test 58 of 71

DIME Test ID: 2019-01-08-1-59
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Bolt Length no data in
Measurement Average 3.99 mils

Test 59 of 71

DIME Test ID: 2019-01-08-1-60
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Bolt Length no data in
Measurement Average 4.5 mils

Test 60 of 71

DIME Test ID: 2019-01-08-1-61
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 407093A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size .625 in
Bolt Length no data in
Measurement Average 3.95 mils

Test 61 of 71

DIME Test ID: 2019-01-08-1-62
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.88 mils

Test 62 of 71

DIME Test ID: 2019-01-08-1-63
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.93 mils

Test 63 of 71

DIME Test ID: 2019-01-08-1-64
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.54 mils

Test 64 of 71

DIME Test ID: 2019-01-08-1-65
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.67 mils

Test 65 of 71

DIME Test ID: 2019-01-08-1-66
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1E
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.28 mils

Test 66 of 71

DIME Test ID: 2019-01-08-1-67
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1F
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 2.89 mils

Test 67 of 71

DIME Test ID: 2019-01-08-1-68
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1G
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Measurement Average 3.54 mils

Test 68 of 71

DIME Test ID: 2019-01-08-1-69
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 38.5
Spacing Ok

Test 69 of 71

DIME Test ID: 2019-01-08-1-70
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 39.5
Spacing Ok

Test 70 of 71

DIME Test ID: 2019-01-08-1-71
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 40.95
Spacing Ok

Test 71 of 71

DIME Test ID: 2019-01-08-1-72
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 01/10/2019
Date Tested: 01/10/2019
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1D
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 310706
Finish Coating ASTM B695 - Mech Galv
Product Markings WS
Size .625 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 41.3
Spacing Ok