Print Report | Back to Sample Detail

Sample Record for 2017-07-18-19

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211948 DEA: 073W2204 EFIS: 0716000011 QA Service Level: 1
DIST-CO-RTE-PM: 07-LA-210-R0.0/R15.8
Work Description: REPLACE BRIDGE APPROACH SLABS AND REHABILITATE DECKS.
Location Description: LOS ANGELES COUNTY IN LOS ANGELES AND GLENDALE FROM NORTH CONNECTOR OVERCROSSING TO HONOLULU AVENUE UNDERCROSSING
Contractor Name: West Coast Structures, Inc.
Contractor Address: 6005 Tyler St., Riverside, CA,92503
Resident Engineer: Patricia Amadi Structure Rep.: Adriana Pimienta

Sample Information

DIME Sample ID: 2017-07-18-19
TL Number from the TL Form: C940652
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 07/18/2017
Date that the sample was received by the laboratory/organization performing the testing: 07/21/2017
The quantity of what the sample constitutes: 1
A brief description of the sample: A307A Threaded Rod
From where was the sample collected: Fabricator
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Ulmer Industries

Material Information

Rocap Number(s):
Heat Number(s): 405414
Nut Mfg. Lot Number(s):
Washer Mfg. Lot Number(s):
Bolt Specification: A307A
Bolt Length(s): 3'-8"
Nut Specification: NA
Washer Specification: NA
Finish: A153 / F2329
Diameter/Size: .750
Bolt Mfg. Lot Number: 1
Rocap Test Requirement(s):
Lubricant Requirements(s):
Test results on following page(s): 3

Test Results

Test 1 of 3

DIME Test ID: 2017-07-18-19-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A307 A Threaded Stud
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
1AA307 A .750\" x 44\" threaded Rod0.33425620113767076461321581A307 A Threaded Stud
UTM 400KIP
Temperature 72

Test 2 of 3

DIME Test ID: 2017-07-18-19-2
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 405414
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A307 A
Size .750 in
Bolt Length 44 in
Gage Type Pass

Test 3 of 3

DIME Test ID: 2017-07-18-19-3
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 07/24/2017
Date Tested: 07/24/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) 405414
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A307 A
Size .750 in
Bolt Length 44 in
Measurement Average 5.31 mils