Print Report | Back to Sample Detail

Sample Record for 2017-06-21-1

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 211718 DEA: 120H5304 EFIS: 1213000147 QA Service Level: 1
DIST-CO-RTE-PM: 12-ORA-5-6.8,22.8
Work Description: BRIDGE RAIL UPGRADE AND DECK REPLACEMENT
Location Description: ORANGE COUNTY IN SAN JUAN CAPISTRANO AND IRVINE AT NORTHBOUND CAMINO LAS RAMBLAS LOOP ON RAMP AND NEAR BEE CANYON CREEK
Contractor Name: UNITED ENGINEERING & CONSTRUCTION, INC
Contractor Address: 336 N Central Ave, Glendale, CA 91203
Resident Engineer: Irvin Nguyen Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-06-21-1
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT - Unassigned/General Field Laboratory
Sample Organization Contact: 5625005861
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 06/21/2017
Date that the sample was received by the laboratory/organization performing the testing: 06/26/2017
The quantity of what the sample constitutes: 16 and 36
A brief description of the sample: A325 MG
From where was the sample collected: Fabricator
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Structural and Steel Products

Material Information

Rocap Number(s): 170613B 170613A
Heat Number(s): NF15102338 CR10356300
Nut Mfg. Lot Number(s): 38621366009A 3A
Washer Mfg. Lot Number(s): 21445870 512224
Bolt Specification: A325
Bolt Length(s): 2 1/2" 2 1/4"
Nut Specification: A563
Washer Specification: F436
Finish: MG
Diameter/Size: 3/4 5/8
Bolt Mfg. Lot Number: DL16105190 NF15101077
Rocap Test Requirement(s): Yes
Lubricant Requirements(s): Yes

Test Results

Test 1 of 14

DIME Test ID: 2017-06-21-1-1
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 367173A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325
Size 0.75 in
Bolt Length 1 in
Gage Type Pass

Test 2 of 14

DIME Test ID: 2017-06-21-1-2
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 367173A
Finish Coating ASTM B695 - Mech Galv
Product Markings A325
Size 0.75 in
Bolt Length 1 in
Measurement Average 2.93 mils

Test 3 of 14

DIME Test ID: 2017-06-21-1-4
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 386213A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size 0.75 in
Bolt Length no data in
Measurement Average 3.47 mils

Test 4 of 14

DIME Test ID: 2017-06-21-1-5
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D1287
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 0.75 in
Bolt Length no data in
Measurement Average 3.73 mils

Test 5 of 14

DIME Test ID: 2017-06-21-1-6
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 367173A
Finish Coating ASTM F2329 - Hot Dip
Product Markings A325
Size 0.75 in
Bolt Length 1 in
Hardness Reading Scale C Scale
Hardness Reading Average 29
Spacing Ok

Test 6 of 14

DIME Test ID: 2017-06-21-1-7
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D1287
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 0.75 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 40.95
Spacing Ok

Test 7 of 14

DIME Test ID: 2017-06-21-1-8
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 747712
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 LE
Size 0.625 in
Bolt Length 2.25 in
Gage Type Pass

Test 8 of 14

DIME Test ID: 2017-06-21-1-9
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 747712
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 LE
Size 0.625 in
Bolt Length 2.25 in
Measurement Average 3.06 mils

Test 9 of 14

DIME Test ID: 2017-06-21-1-10
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 747712
Finish Coating ASTM B695 - Mech Galv
Product Markings A325 LE
Size 0.625 in
Bolt Length 2.25 in
Hardness Reading Scale C Scale
Hardness Reading Average 30.9
Spacing Ok

Test 10 of 14

DIME Test ID: 2017-06-21-1-11
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 366009A
Finish Coating ASTM B695 - Mech Galv
Product Markings DH N
Size 0.625 in
Bolt Length no data in
Measurement Average 3.14 mils

Test 11 of 14

DIME Test ID: 2017-06-21-1-12
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D0920
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 0.625 in
Bolt Length no data in
Measurement Average 4.35 mils

Test 12 of 14

DIME Test ID: 2017-06-21-1-13
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number D0920
Finish Coating ASTM B695 - Mech Galv
Product Markings F436 P
Size 0.625 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 42.4
Spacing Ok

Test 13 of 14

DIME Test ID: 2017-06-21-1-14
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1AL53-135-17.75\"50861226.24Nut Proof LoadBrian
UTM 400KIP
Temperature 71 F

Test 14 of 14

DIME Test ID: 2017-06-21-1-15
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 06/28/2017
Date Tested: 06/27/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof Load
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
2AL53-135-175/8\"34575153.8Nut Proof LoadBrian
UTM 400KIP
Temperature 71 F