Print Report | Back to Sample Detail

Sample Record for 2017-05-31-3

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 212468 DEA: 113A0534 EFIS: 1117000127 QA Service Level: 1
DIST-CO-RTE-PM: 11-SD-75-
Work Description:
Location Description:
Contractor Name: Traffic Development Services
Contractor Address: 207 W Los Angeles Ave. , Ste 252, Moorpark ,CA 93021
Resident Engineer: Trung Minh Tran Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2017-05-31-3
TL Number from the TL Form: Unknown
Sample Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Sample Organization Contact: (530) 329-6527
Type of Sample: Quality Assurance
Type of Material: SMTL TM3 - Fastener Assembly
Sample Taken Date: 05/31/2017
Date that the sample was received by the laboratory/organization performing the testing: 06/02/2017
The quantity of what the sample constitutes: 4
A brief description of the sample: F1554, A449
From where was the sample collected: Distributor
Laboratory sample identification: Unknown
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Universal Industrial Sales, Wrought Washer Mfg Inc Platte Decker

Material Information

Rocap Number(s):
Heat Number(s): PL16106308
Nut Mfg. Lot Number(s): NR791, 16-41-009
Washer Mfg. Lot Number(s): 230608
Bolt Specification: F1554-55, A449
Bolt Length(s): 3", 12"
Nut Specification: A5463
Washer Specification: F436
Finish: HDG
Diameter/Size: 1.5", 1"
Bolt Mfg. Lot Number: 166707
Rocap Test Requirement(s):
Lubricant Requirements(s):

Test Results

Test 1 of 19

DIME Test ID: 2017-05-31-3-1
Test Method: ASTM F606-14: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Hex Cap Screws)
Verified Date: 06/28/2017
Date Tested: 06/07/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: A449 Rod & Nut
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleSizeArea (in^2)Peak Load (lbf)Peak Load (kN)Tensile Strength (psi)Stress at Offset (psi)Load at Offset (lbf)Comments
2AA449 1\" x 12\" w / Nut0.6068362137113798912565576147A449 Rod & Nut
UTM 400KIP
Temperature 72

Test 2 of 19

DIME Test ID: 2017-05-31-3-6
Test Method: ASTM F606-14a: Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets (Proof Load)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test: Nut Proof
Test Result Compliance:
Additional Comments When Verified:
Number of Samples 1
SampleBolt Mfg. Lot NumberSize (in)Peak Load (lbf)Peak Load (kN)CommentsTested By
1AL02-035-171 1/2\"213970951.79Nut ProofBrian
UTM 400KIP
Temperature 71 F

Test 3 of 19

DIME Test ID: 2017-05-31-3-7
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number NR791
Finish Coating ASTM A153 - Hot Dip
Product Markings U DH
Size 1.5 in
Gage Type Pass

Test 4 of 19

DIME Test ID: 2017-05-31-3-8
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) PL16106308
Mfg. Lot Number no data
Finish Coating Plain
Product Markings YELLOW
Size 1.5 in
Bolt Length no data in
Gage Type Fail (Go)

Test 5 of 19

DIME Test ID: 2017-05-31-3-9
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Gage Type Pass

Test 6 of 19

DIME Test ID: 2017-05-31-3-10
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Gage Type Pass

Test 7 of 19

DIME Test ID: 2017-05-31-3-11
Test Method: ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Gage Type Pass

Test 8 of 19

DIME Test ID: 2017-05-31-3-12
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Gage Type Pass

Test 9 of 19

DIME Test ID: 2017-05-31-3-13
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Gage Type Pass

Test 10 of 19

DIME Test ID: 2017-05-31-3-14
Test Method: ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Gage Type Pass

Test 11 of 19

DIME Test ID: 2017-05-31-3-15
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Measurement Average 6.7 mils

Test 12 of 19

DIME Test ID: 2017-05-31-3-16
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Measurement Average 5.18 mils

Test 13 of 19

DIME Test ID: 2017-05-31-3-17
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) 166707
Mfg. Lot Number no data
Finish Coating ASTM F2329 - Hot Dip
Product Markings A449
Size 1 in
Bolt Length 12 in
Measurement Average 5.41 mils

Test 14 of 19

DIME Test ID: 2017-05-31-3-18
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Bolt Length no data in
Measurement Average 3.04 mils

Test 15 of 19

DIME Test ID: 2017-05-31-3-19
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2B
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Bolt Length no data in
Measurement Average 2.94 mils

Test 16 of 19

DIME Test ID: 2017-05-31-3-20
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 2C
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 16-41-009
Finish Coating ASTM F2329 - Hot Dip
Product Markings DH DMC
Size 1 in
Bolt Length no data in
Measurement Average 4.8 mils

Test 17 of 19

DIME Test ID: 2017-05-31-3-21
Test Method: ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 230608
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Hardness Reading Scale C Scale
Hardness Reading Average 41.4
Spacing Ok

Test 18 of 19

DIME Test ID: 2017-05-31-3-22
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number 230608
Finish Coating ASTM F2329 - Hot Dip
Product Markings WS
Size 1.5 in
Bolt Length no data in
Measurement Average 2.9 mils

Test 19 of 19

DIME Test ID: 2017-05-31-3-23
Test Method: ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)
Verified Date: 06/28/2017
Date Tested: 06/28/2017
Submitted By Organization: CT HQ - Sacramento Structural Materials Testing Laboratory
Organization Address: 5900 Folsom Boulevard,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: joshua.moore@dot.ca.gov
Organization Phone: (530) 329-6527
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Sample No. 1A
Rocap Number no data
Heat Number(s) no data
Mfg. Lot Number NR791
Finish Coating ASTM F2329 - Hot Dip
Product Markings U DH
Size 1.5 in
Bolt Length no data in
Measurement Average 2.9 mils

Tests Assigned to this Sample

DIME Test IDTest MethodAssigned DateTest DateAssigned ByAssigned LabTest CommentsAssigned To
2017-05-31-3-2ASME B1.2-83r01: (Plug Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Plug Gage)06/28/201706/28/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-05-31-3-3ASME B1.2-83r01: (Ring Gage) Gages and Gaging for Unified Inch Screw Threads - Errata May 1992 (Ring Gage)06/28/201706/28/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-05-31-3-4ASTM B499-14: Standard Test Method for Measurement of Coating Thicknesses by the Magnetic Method: Nonmagnetic Coatings on Magnetic Basis Metals (Coating)06/28/201706/28/2017Fred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor
2017-05-31-3-5ASTM E18-15: Standard Test Methods for Rockwell Hardness of Metallic Materials (Hardness)06/28/2017Not scheduledFred SaylorCT HQ - Sacramento Structural Materials Testing LaboratoryFred Saylor