Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 215603 DEA: 032G1004
QA Service Level: 1
DIST-CO-RTE-PM: 03-ED-49-9.6/14.2
Work Description: COLD PLANE AC PAVEMENT AND HMA OVERLAY.
Location Description: EL DORADO COUNTY IN AND NEAR PLACERVILLE FROM PLEASANT VALLEY ROAD TO 0.2 MILE SOUTH OF GILMORE STREET
Contractor Name: GEORGE REED INC
Contractor Address: Unknown
Resident Engineer: Unknown Structure Rep.: Unknown
DIME Sample ID: 2021-07-22-42
TL Number from the TL Form:
Sample Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Sample Organization Contact: (530) 741-4238
Type of Sample: Verification
Type of Material: Hot Mix Asphalt
Sample Taken Date: 07/22/2021
Date that the sample was received by the laboratory/organization performing the testing: 07/22/2021
The quantity of what the sample constitutes: 20 boxes of mix
A brief description of the sample: 1/2" HMA-A
From where was the sample collected: Supplier
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: George Reed Batch Plant
DIME Test ID: 2021-07-22-42-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 09/03/2021
Date Tested: 07/23/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
What temperature unit is used?
|
Fahrenheit
|
Test procedure used?
|
no data
|
Mass of HMA Sample prior to ignition
|
no data
|
Corrected Asphalt Binder Content
|
5.30 %
|
Mass Loss
|
no data
|
Correction Factor (Percent by mass of HMA Specimen)
|
no data
|
Moisture Content
|
no data
|
Temperature Compensation Factor
|
no data
|
Test Temperature
|
no data
|
DIME Test ID: 2021-07-22-42-2
Test Method: AASHTO T275-07r12: Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-Coated Specimens (Bulk Specific Gravity)
Verified Date: 09/03/2021
Date Tested: 07/20/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
Bulk Specific Gravity
|
2.475
|
Bulk Specific Gravity 2
|
2.483
|
Bulk Specific Gravity 3
|
2.480
|
Average Bulk Specific Gravity
|
2.479
|
DIME Test ID: 2021-07-22-42-3
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 09/03/2021
Date Tested: 07/16/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
Number of tests
|
1
|
What is the unit of measurement for theoretical density?
|
US Units
|
Mass Determination
|
Air
|
Specific Gravity for Sample 1
|
2.569
|
Theoretical maximum density at 25°C (77°F)
|
no data
|
DIME Test ID: 2021-07-22-42-4
Test Method: AASHTO T269-14: Standard Method of Test for Percent Air Voids in Compacted Dense and Open Asphalt Mixtures (Air Void)
Verified Date: 09/03/2021
Date Tested: 07/13/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
Percent Air Voids
|
3.7 %
|
Percent Air Voids 2
|
3.4
|
Percent Air Voids 3
|
3.5
|
Percent Air Voids Average
|
3.5
|
DIME Test ID: 2021-07-22-42-5
Test Method: AASHTO T283-14: Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage (Moisture Content)
Verified Date: 09/03/2021
Date Tested: 07/26/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
Unit system used?
|
SI Units
|
Average Dry Tensile Strength
|
165 psi
|
Average Wet Tensile Strength
|
128 psi
|
Tensile Strength Ratio
|
0.78
|
DIME Test ID: 2021-07-22-42-6
Test Method: AASHTO T324-14: Standard Method of Test for Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures (Hamburg Wheel Track)
Verified Date: 09/03/2021
Date Tested: 07/26/2021
Submitted By Organization: CT D03 - Olivehurst Northern Regional Laboratory
Organization Address: 5330 Arboga Road,
Organization City: Olivehurst
Organization State: CA
Organization Zipcode: 95961
Organization Email: jeff.herbert@dot.ca.gov
Organization Phone: (530) 741-4238
General Comments for this Test: JMF 21-032
Test Result Compliance:
Additional Comments When Verified:
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel A)
|
25000
|
Specified minimum number of passes at ½” rut depth, or number of passes at ½” rut depth if applicable (Wheel B)
|
20540
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel A)
|
9.85 mm
|
Impression at specified number of passes, or specified maximum impression if applicable (Wheel B)
|
12.72 mm
|
Stripping Inflection Point (Wheel A)
|
22829
|
Stripping Inflection Point (Wheel B)
|
18438
|