Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.
Project ID: 215252 DEA: 021J4704 EFIS: 0220000082
QA Service Level: 1
DIST-CO-RTE-PM: 02-TRI-3-46.7/49.8,63.8/67.704
Work Description: HMA OVERLAY, REPLACE AC SURFACING AND SHOULDER BACKING.
Location Description: TRINITY COUNTY NEAR TRINITY CENTER FROM 0.7 MILE NORTH OF CEDAR STOCK ROAD TO DIENER MINE VIADUCT AND FROM 2.3 MILES NORTH OF EL DORADO WAY TO COFFEE CREEK BRIDGE NO. 05-0060
Contractor Name: J.F. SHEA CONSTRUCTION, INC.
Contractor Address: 17400 CLEAR CREEK RD, REDDING CA 96001
Resident Engineer: Structure Rep.: Unknown
DIME Sample ID: 2021-05-11-28
TL Number from the TL Form: 768792
Sample Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Sample Organization Contact: (530) 225-3194
Type of Sample: Acceptance
Type of Material: Reclaimed Asphalt Pavement
Sample Taken Date: 05/11/2021
Date that the sample was received by the laboratory/organization performing the testing: 05/11/2021
The quantity of what the sample constitutes: Production Start-Up Evaluation
A brief description of the sample: 3/8-inch RAP (Combined)
From where was the sample collected: Manufacturer
Laboratory sample identification: D78794B
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: J F Shea Construction - Fawndale Rock and Asphalt - Redding, CA
RAP Source: Fawndale Rock and Asphalt, Redding, CA
Aggregate Size: 3/8-inch
Aggregate Source:
RAP Stockpile:
Stockpile Size (tons):
Reclaimed Asphalt Pavement Mix Number:
DIME Test ID: 2021-05-11-28-1
Test Method: AASHTO T308-10: Standard Method of Test for Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the Ignition Method (Method A) (Asphalt Binder Content)
Verified Date: 07/09/2021
Date Tested: 05/13/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
What temperature unit is used?
|
Fahrenheit
|
Test procedure used?
|
Method A
|
Mass of the specimen basket assembly
|
no data
|
Mass of the specimen and specimen basket assembly prior to ignition
|
no data
|
Mass of HMA Sample prior to ignition
|
1666.7 g
|
Corrected Asphalt Binder Content
|
6.03 %
|
Mass Loss
|
no data
|
Mass of aggregate remaining after ignition
|
1563.2 g
|
Correction Factor (Percent by mass of HMA Specimen)
|
0.00 %
|
Moisture Content
|
0.18 %
|
Temperature Compensation Factor
|
no data
|
Test Temperature
|
1000 F
|
DIME Test ID: 2021-05-11-28-2
Test Method: AASHTO T30-19: Standard Method of Test for Mechanical Analysis of Extracted Aggregate (Mechanical Analysis)
Verified Date: 07/09/2021
Date Tested: 05/14/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance:
Additional Comments When Verified:
Is an aggregate correction factor used?
|
No
|
Cumulative percent passing the 2 in. sieve
|
100 %
|
Cumulative percent passing the 1 1/2 in. sieve
|
100 %
|
Cumulative percent passing the 1 in. sieve
|
100 %
|
Cumulative percent passing the 3/4 in. sieve
|
100 %
|
Cumulative percent passing the 1/2 in. sieve
|
100 %
|
Cumulative percent passing the 3/8 in. sieve
|
99.7 %
|
Cumulative percent passing the 1/4 in. sieve
|
83.6 %
|
Cumulative percent passing the #4 sieve
|
68.3 %
|
Cumulative percent passing the #8 sieve
|
45.3 %
|
Cumulative percent passing the #16 sieve
|
31.8 %
|
Cumulative percent passing the #30 sieve
|
23.4 %
|
Cumulative percent passing the #50 sieve
|
17.3 %
|
Cumulative percent passing the #100 sieve
|
12.9 %
|
Cumulative percent passing the #200 sieve
|
10.0 %
|
DIME Test ID: 2021-05-11-28-3
Test Method: AASHTO T209-12: Standard Method of Test for Theoretical Maximum Specific Gravity (Gmm) and Density of Asphalt Mixtures (Maximum Specific Gravity)
Verified Date: 07/09/2021
Date Tested: 05/13/2021
Submitted By Organization: CT D02 - Redding Northern Regional Laboratory
Organization Address: 1657 Riverside Drive,
Organization City: Redding
Organization State: CA
Organization Zipcode: 96001
Organization Email: ward.jenkins@dot.ca.gov
Organization Phone: 530-225-3194
General Comments for this Test:
Test Result Compliance: complies
Additional Comments When Verified:
Number of tests
|
1
|
What is the unit of measurement for theoretical density?
|
US Units
|
Mass Determination
|
Air
|
Method Performed
|
Mechanical Agitation - Method A
|
Mass of container filled with water
|
7336.6 grams
|
Mass of oven-dry sample in air for Sample 1
|
1565.2 grams
|
Mass of container filled with the sample and water for Sample 1
|
8279.2 grams
|
Temperature of Water
|
77 °F
|
Specific Gravity for Sample 1
|
2.514
|
Theoretical maximum density at 25°C (77°F)
|
no data
|