Print Report | Back to Sample Detail

Sample Record for 2021-06-14-35

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215250 DEA: 021J4404 EFIS: 0220000079 QA Service Level: 1
DIST-CO-RTE-PM: 02-MOD-299-20.0/23.1,23.5/24.5,33.5/37.5
Work Description: ASPHALT RUBBER CHIP SEAL.
Location Description: MODOC COUNTY AT VARIOUS LOCATIONS FROM 1.8 MILES WEST OF ROUTE 139 TO 0.3 MILE WEST OF RATTLESNAKE CREEK BRIDGE
Contractor Name: AMERICAN PAVEMENT SYSTEMS , Inc.
Contractor Address: 1012 11th Street, Modesto, CA 95354
Resident Engineer: Tofael Anwar Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-06-14-35
TL Number from the TL Form: c853347
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Acceptance
Type of Material: Asphalt Binder
Sample Taken Date: 06/14/2021
Date that the sample was received by the laboratory/organization performing the testing: 06/24/2021
The quantity of what the sample constitutes: 2 cans
A brief description of the sample: PG64-28M
From where was the sample collected: Manufacturer
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Eagle Peak Rock, Alturas, CA

Material Information

Performance Grade: PG 64-28 M
Modified: Yes
Lot number: 1
Sublot number: 1
Tank number:
Time of sample:
HMA Supplier: Eagle Peak Alturas
Certified Asphalt Supplier: Albina Asphalt - Klamath Falls Plant - Klamath Falls OR
Multigrade: No
Multigrade Type:
Asphalt Binder Mix Number:

Test Results

Test 1 of 4

DIME Test ID: 2021-06-14-35-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 06/29/2021
Date Tested: 06/28/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Standard Specifications
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? no data
Mass of empty container #1 164.583 grams
Mass of empty container #2 160.424 grams
Mass of container #1 before test (m1i) 214.320 grams
Mass of container #2 before test (m2i) 213.360 grams
Mass of container #1 after test (m1f) 214.247 grams
Mass of container #2 after test (m2f) 213.273 grams
Average mass change -0.156 percent

Test 2 of 4

DIME Test ID: 2021-06-14-35-2
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/29/2021
Date Tested: 06/28/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Standard Specifications ORIG
Test Result Compliance: complies
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.173 kPa
Phase Angle (δ) (for the 10 cycles) 73.2 degree
Complex Modulus (G*) (for the 10 measurements) 1.442 kPa
Test Temperature (Specimen 1) 64.0 C
Dynamic Shear, G*/sin(δ) 1.51 kPa

Test 3 of 4

DIME Test ID: 2021-06-14-35-3
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/29/2021
Date Tested: 06/28/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 Standard Specifications RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.268 kPa
Phase Angle (δ) (for the 10 cycles) 69.6 degree
Complex Modulus (G*) (for the 10 measurements) 2.683 kPa
Test Temperature (Specimen 1) 64.0 C
Dynamic Shear, G*/sin(δ) 2.86 kPa

Test 4 of 4

DIME Test ID: 2021-06-14-35-4
Test Method: AASHTO T315-20: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/29/2021
Date Tested: 06/28/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: RTFO+6, Delta @ 2.2 kPa = 70.4
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.146 kPa
Phase Angle (δ) (for the 10 cycles) 71.2 degree
Complex Modulus (G*) (for the 10 measurements) 1.465 kPa
Test Temperature (Specimen 1) 70.0 C
Dynamic Shear, G*/sin(δ) 1.55 kPa