Print Report | Back to Sample Detail

Sample Record for 2021-05-24-38

Note: Fields with no data or with a value of "Unknown" will not be displayed on the print out.

Project Information

Project ID: 215253 DEA: 021J4804 EFIS: 0220000083 QA Service Level: 1
DIST-CO-RTE-PM: 02-SHA,TRI-36-8.0/11.912,27.1/R41.139
Work Description: ASPHALT RUBBER CHIP SEAL AND TRAFFIC STRIPE.
Location Description: SHASTA AND TRINITY COUNTIES AT AND NEAR PLATINA FROM 0.4 MILE EAST OF MIDDLE FORK COTTONWOOD CREEK BRIDGE TO BEEGUM CREEK BRIDGE AND FROM 1.3 MILES EAST OF BRAMLET ROAD TO SHASTA COUNTY LINE
Contractor Name: NORTHWEST PAVING, INC
Contractor Address: 8115 SECLUDED VALLEY DRIVE;, REDDING CA 96001
Resident Engineer: Structure Rep.: Unknown

Sample Information

DIME Sample ID: 2021-05-24-38
TL Number from the TL Form: 779360
Sample Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Sample Organization Contact: (916) 227-7302
Type of Sample: Acceptance
Type of Material: Asphalt Binder
Sample Taken Date: 05/24/2021
Date that the sample was received by the laboratory/organization performing the testing: 06/17/2021
The quantity of what the sample constitutes: 1 OF 2 CANS
A brief description of the sample: ASPHALT BINDER
From where was the sample collected: Source
Laboratory sample identification:
Structure unique identifier:
Structure name:
The fabricator/manufacturer/facility name: Valero-Benicia Asphalt Plant

Material Information

Performance Grade: PG 58-22
Modified: No
Lot number:
Sublot number:
Tank number:
Time of sample:
HMA Supplier:
Certified Asphalt Supplier: Valero Marketing & Supply - Benicia CA
Multigrade: No
Multigrade Type:
Asphalt Binder Mix Number:
Test results on following page(s): 4

Test Results

Test 1 of 4

DIME Test ID: 2021-05-24-38-1
Test Method: AASHTO T240-17: Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-Film Oven Test)
Verified Date: 06/23/2021
Date Tested: 06/21/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 standard specifications
Test Result Compliance: complies
Additional Comments When Verified:
Is mass change based on one or two containers? Two
Any material loss from containers during heating process/testing? No
Mass of empty container #1 156.612 grams
Mass of empty container #2 167.153 grams
Mass of container #1 before test (m1i) 191.756 grams
Mass of container #2 before test (m2i) 202.103 grams
Mass of container #1 after test (m1f) 191.554 grams
Mass of container #2 after test (m2f) 201.870 grams
Average mass change -0.621 percent

Test 2 of 4

DIME Test ID: 2021-05-24-38-2
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/23/2021
Date Tested: 06/21/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 standard specifications ORIG
Test Result Compliance: does not comply
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.268 kPa
Phase Angle (δ) (for the 10 cycles) 83.5 degree
Complex Modulus (G*) (for the 10 measurements) 2.237 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 2.25 kPa

Test 3 of 4

DIME Test ID: 2021-05-24-38-3
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/23/2021
Date Tested: 06/21/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: RTFO
Test Result Compliance: complies
Additional Comments When Verified:
Phase RTFO residue
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 10.00 %
Stress Amplitude 0.591 kPa
Phase Angle (δ) (for the 10 cycles) 78.2 degree
Complex Modulus (G*) (for the 10 measurements) 5.908 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 6.04 kPa

Test 4 of 4

DIME Test ID: 2021-05-24-38-6
Test Method: AASHTO T315-16: Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) (Dynamic Shear)
Verified Date: 06/23/2021
Date Tested: 06/21/2021
Submitted By Organization: CT HQ - Sacramento Asphalt Binder Laboratory
Organization Address: 5900 Folsom Boulevard, Room 225,
Organization City: Sacramento
Organization State: CA
Organization Zipcode: 95819
Organization Email: guadalupe.magana@dot.ca.gov
Organization Phone: (916) 227-7302
General Comments for this Test: Per 2018 standard specifications ORIG
Test Result Compliance: does not comply
Additional Comments When Verified:
Phase Original binder
Test Plate Diameter 25 mm
Test Gap 1 mm
Test Frequency 10.0 rad/s
Strain Amplitude 12.00 %
Stress Amplitude 0.265 kPa
Phase Angle (δ) (for the 10 cycles) 83.5 degree
Complex Modulus (G*) (for the 10 measurements) 2.208 kPa
Test Temperature (Specimen 1) 58.0 C
Dynamic Shear, G*/sin(δ) 2.22 kPa